The ILED-BH-R330C MLC is a standby-motion-sensor LED ceiling bulkhead designed for corridor and entrance lighting where automatic on off control is preferred. At \u03c6330mm it is the larger round variant in the R330 series, offering higher lumen output than the compact R145 hublot while maintaining the same IP65 weatherproof construction. The integrated PIR sensor runs at a standby level of 10\u201320% when no motion is detected, then switches to full output for a user-adjustable hold time when movement is detected.<\/p>\n
The ILED-BH-R330C MLC runs at a fixed 18W, producing 1980 lumens from a \u03c6330mm housing at 110 lumens per watt. The LED source is LumiLEDs LM80 with a colour rendering index above 82. Input is 220-240VAC or 110-277VAC 50\/60Hz, so the fixture works in most regions without a transformer. The colour temperature range is 2800K to 6500K \u2014 warm white, neutral and cool white \u2014 selectable via a dip-switch inside the housing. The beam angle is 120\u00b0, spreading light evenly across the floor plane. Electrical classification is Class II, meaning the fixture is double-insulated and does not require a protective earth connection. The housing base is ABS with a PS diffuser. The complete assembly is IP65 rated \u2014 dust-tight and protected against water jets from any direction \u2014 making it suitable for covered outdoor locations such as entryways, porches and sheltered walkways.<\/p>\n
The integrated PIR standby motion sensor activates the fixture when movement is detected within its 120\u00b0 detection arc, up to a maximum mounting height of 3.5 metres. The standby level is factory-set to 10\u201320% \u2014 the fixture remains dimly lit between activations to aid navigation, then switches to full output when motion is sensed. The hold time is adjustable from 30 seconds to 10 minutes via a dip-switch. When set to full-off mode, the fixture remains dark until motion is detected. The sensor is factory-installed inside the housing and cannot be removed or retrofitted after installation.<\/p>\n
This is a standard standby-motion-sensor bulkhead with no DALI dimming, 0-10V control, or emergency backup. The sensor hold time and standby level are adjustable via internal dip-switches. For projects that require DALI dimming, self-test emergency or photocell control, order the emergency or wall-packed variants from the Halo round 330mm series instead. These variants share the same \u03c6330mm housing but use different internal drivers and control electronics.<\/p>\n
Each unit ships as a single bulkhead with the driver and PIR sensor pre-installed, mounting hardware included and the terminal block ready for connection. The selected colour temperature is factory-set via the internal dip-switch \u2014 confirm the required setting before ordering, as it cannot be changed after the housing is sealed. No separate controllers, transformers or sensors are packed inside \u2014 the fixture is ready to wire direct to mains.<\/p>\n
The ILED-BH-R330C MLC is built for corridor and entrance positions where automatic lighting control reduces both energy consumption and maintenance calls. Hotel and office corridors use the standby sensor to keep passages dimly lit between movements. Residential entryways and porch areas benefit from the automatic on off \u2014 residents do not need to find a switch in the dark. External walkways and building entrances specify the IP65 seal to handle rain and washdown. Stairwell landings and wider corridor junctions take advantage of the \u03c6330mm size and 1980-lumen output to provide adequate illumination from a single fixture.<\/p>\n
The ILED-BH-R330C MLC carries SAA, CE and RoHS certifications. SAA approval covers Australian and New Zealand market requirements. The warranty period is three to five years depending on the region and distributor terms.<\/p>","protected":false},"excerpt":{"rendered":"
The Standby Sensor Waterproof LED Ceiling Light (ILED-BH-R330C MLC) is a \u03c6330mm round bulkhead built for corridor and entrance illumination with an integrated PIR motion sensor. It runs at 18W producing 1980 lumens at 110 lumens per watt from a LumiLEDs LM80 source. The ABS housing base and PS diffuser are IP65 sealed for covered outdoor use, and the Class II electrical rating means no protective earth is required. Three colour temperatures are selectable at installation via an internal dip-switch.<\/p>","protected":false},"featured_media":13190,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[161,149],"product_tag":[324,294,295,247,254],"class_list":["post-13189","product","type-product","status-publish","has-post-thumbnail","product_cat-commercial-led-light","product_cat-led-bulkhead-light","product_tag-amenity-lighting","product_tag-area-lighting","product_tag-commercial-lighting","product_tag-ip65","product_tag-sensor","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product\/13189","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/comments?post=13189"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media\/13190"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media?parent=13189"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_brand?post=13189"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_cat?post=13189"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_tag?post=13189"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}