The ILED-DM2 A is a 3-zone single color dimmer controller for 12V and 24V LED strips. Three zones fade to their own levels, all on one color. It is driven by a 2.4G remote and by a push button on the body. There is no pair code and no app. It suits shops, offices, corridors, and homes where one color is enough.<\/p>\n
Three zones means three independent fade levels, all on one color. Zone 1 can hold 100%, Zone 2 at 50%, and Zone 3 off. Use that to stage a room: 100% over the counter, 50% in the corridor, 0% under the bed. Each zone has its own 4A channel, so the three do not share a single dimming current. The layout suits a house where each room has its own strip and you want them to differ, but every one is the same warm white.<\/p>\n
The 2.4G remote sends over radio, not over cables. Each channel has its own address, so the three zones fade independently without cross-talk. The remote is RF 2.4GHz, so no line of sight is needed. The receiver and remote keep their settings when the power goes off. The push button on the body does the same jobs as the remote, so you are not stuck if the remote is misplaced. There is no pairing step: power it up and it runs.<\/p>\n
Each of the three channels is rated at 4A, so the controller drives up to 144W on a 12V system or 288W on a 24V system. Dimming runs from 0 to 100%, and the fade is smooth. At low levels the strip holds a clean 10% without flicker. The output is a DC2.1 plus a screw terminal, so you can use a DC plug or a wire. For a long strip, run a separate 12V or 24V power supply to the strip and use this controller only for the dimming signal.<\/p>\n
Feed the controller from a DC2.1 plug or from the screw terminal. It runs on a 12V to 24V DC supply. You need a matching 12V or 24V power supply sized to your strip, with a few volts above the strip’s nominal rating for the long runs. Do not exceed 4A on any one channel. For 3 zones, connect each strip’s plus and signal to its own channel and share the common ground.<\/p>\n
The receiver measures L85 by W45 by H23mm and weighs 45g. The remote measures L150 by W40 by H13mm and weighs 60g. The remote fits in one hand and has buttons for each of the 3 zones. The receiver bolts to your desk or wall. Both carry their settings across a power cut. The packaging ships in a colorful box or skin pack, and OEM is supported.<\/p>\n
It is rated from -30C to +55C, which covers most indoor and sheltered outdoor use. For an outdoor install, mount it under a canopy where the sun does not hit it directly. The 2.4G signal needs a clear path or a short cable, not a wall between the remote and the receiver. The flicker-free output suits camera work, product photos, and retail displays. Use it where a dimmer that fades three zones on one color is the whole job.<\/p>\n
Three zones of one color covers most commercial jobs: shops, offices, corridors, and museum cases. A single warm white is enough for a retail floor and a hallway. Where you do need color, the ILED-DM2 D (RGBW, 4 zones, 5A x 4CH) or the ILED-DM2 E (5-zone RGB+CCT, 5A x 5CH) are the right sibling. This one is the no-frills dimmer.<\/p>\n
Each order ships one ILED-DM2 A receiver and one 2.4G remote, in a colorful box or skin pack. It has a DC2.1 input and screw terminals for 3 channels, plus 3 push buttons for local control. No cables, connectors, or power supply are included. Add a 12V or 24V supply and a matching strip.<\/p>\n
A 12V or 24V power supply sized to the strip. A strip that is within the 4A per channel limit. A mount for the receiver, and a clear path or a short cable for the remote. The remote battery comes with the unit. Everything else is in the box. Do not exceed the 4A per channel.<\/p>\n
Use the ILED-DM2 A on retail and office strips, corridor and under-cabinet lines, museum and display cases, and shop signage. It suits single-warm-white systems where three rooms each need a different brightness. For an RGB or CCT mix, move to a sibling model.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-DM2 A is a 3-zone single color dimmer controller for 12V-24V LED strips. Three zones each fade to their own level, all on one color. Output is 4A per channel across 3 channels, so up to 144W at 12V or 288W at 24V. It is driven by a 2.4G remote and by a push button on the body, no pair code. Works with SMD and COB strips. Dimming runs 0 to 100%, flicker-free. It is rated from -30 to +55C and ships in a colorful box or skin pack. It suits shops, offices, corridors, and homes.<\/p>","protected":false},"featured_media":13775,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[240,158],"product_tag":[300],"class_list":["post-13770","product","type-product","status-publish","has-post-thumbnail","product_cat-dimmer-and-controller","product_cat-strip-and-module-lights","product_tag-2-4g","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product\/13770","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/comments?post=13770"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media\/13775"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media?parent=13770"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_brand?post=13770"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_cat?post=13770"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_tag?post=13770"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}