The ILED-BH-015 B is the narrow-beam member of the 015 wall light family. It is a small aluminium bar, 145\u00d755\u00d740mm, carrying two 3W LED sources behind 10-degree glass lenses, and it exists for the jobs a wide wash cannot do: throwing a tight beam a long way up a column, lining a door frame with light, or picking out the vertical joints of a facade one strip at a time. The body comes in black or white, sealed to IP54 for sheltered exterior walls, and it runs the same Class I wiring and order-time colour choice as the rest of the family \u2014 the beam is what makes it different.<\/p>\n
A 10-degree lens is a specialist tool. Held close to the wall it draws a narrow stripe of light; set back, it reaches further up the surface than a wide lens could, at the cost of covering less of it. Each fitting carries two of these beams from its 3W sources, with colour rendering above 80 and a colour temperature specified at order across 2800K to 6500K. The result is architecture-by-nightlight: the wall is drawn in lines rather than flooded, which is the effect designers ask for on columns and formal entrances. Because the beam is tight, spacing matters \u2014 fittings placed at regular centres repeat the stroke down a long surface, while a single fitting picks out one column or one frame without spilling onto its neighbours.<\/p>\n
The body is aluminium with tempered glass lenses, closed on a silicone gasket and sealed to IP54 against dust and splashing water. That rating is the honest fit for this fitting: it goes on porch ceilings, under soffits, on column faces under a canopy, and other sheltered positions where the narrow beam does its work without the full rain on it. The finish is black or white, and at 40mm deep the bar sits close to the surface it lights \u2014 which is also why the rating matters: a fitting this close to the wall has no room for a bulky weather hood, so it belongs where the shelter is already built in.<\/p>\n
The fixture runs on 220-240VAC or 120VAC, Class I wired, with the driver inside the body \u2014 no separate box behind the bar, which matters on a fitting this slim. Colour temperature is locked in at order; there is no switch to change it afterwards, so confirm it when you specify. Warm 2800K\u20133000K flatters stone and timber columns, while 4000K and above read as contemporary on render and metal.<\/p>\n
Installation is a surface mount onto the supplied back plate. An Allen key in the accessories opens the body; mark, drill and plug the wall, fix the plate, terminate live, neutral and earth into the terminal block, and close the body over the gasket. The earth connection is mandatory on this Class I fitting, so an electrician should make the connection. Keep the gasket seat clean when the body closes, because the IP54 rating depends on it.<\/p>\n
Columns and pillars are the classic job: the 10-degree beam climbs the stone from top to bottom in one narrow stroke. Door frames and entry recesses take it as a light lining. Facades with strong vertical structure \u2014 ribs, fins, brick piers \u2014 run it in repeats down the joints. It also suits signs and nameplates that need a tight pool of light, and garden features under a pergola or porch roof where the fitting stays sheltered. Run several along a colonnade or a covered walkway and the regular strokes give the route a rhythm that a single wide wash would flatten out.<\/p>\n
The ILED-BH-015 B carries SAA for Australia and New Zealand, CE for Europe, and RoHS. The sealed body needs no routine work inside; a wipe of the lenses during site maintenance keeps the beams clean.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-BH-015 B is a slim 145\u00d755\u00d740mm LED wall light that throws two 3W beams through 10-degree glass lenses, making it the narrow-beam member of the range: a tight, long throw for columns, door frames and the dividing lines of a facade. The aluminium body is sealed to IP54 for sheltered exterior walls, in black or white, running on 220-240VAC or 120VAC, Class I wired, with colour temperature across 2800\u20136500K at order and CRI above 80. SAA, CE and RoHS.<\/p>","protected":false},"featured_media":14369,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[160,236],"product_tag":[305,316,317,307],"class_list":["post-14364","product","type-product","status-publish","has-post-thumbnail","product_cat-landscape-led-light","product_cat-led-wall-mounted-light","product_tag-decorative-lighting","product_tag-facade-lighting","product_tag-landscape-lighting","product_tag-spot-lighting","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product\/14364","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/comments?post=14364"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media\/14369"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/media?parent=14364"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_brand?post=14364"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_cat?post=14364"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/es\/wp-json\/wp\/v2\/product_tag?post=14364"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}