The ILED-COB-480 24V 10MM is a Chip-on-Board (COB) LED tape light designed for continuous, dotless linear illumination in cove, under-cabinet, accent and architectural lighting. The 24VDC-only variant delivers 900 lm per metre at 9 W/m (100 lm/W) from 480 COB LED positions packed into a 10 mm wide flexible PCB. Unlike traditional SMD strips that show individual light points, the COB process produces a smooth, continuous line of light — ideal for exposed coves and direct-view installations.
Краткий обзор технических характеристик
Model: ILED-COB-480 24V 10MM
LED density: 480 LEDs/metre
Power consumption: 9 W/m
Lumen output: 900 lm/m
Luminous efficacy: 100 lm/W
Beam angle: 180°
Colour temperature: 2700K – 6000K (warm white to cool white)
CRI: >90
Input voltage: 24VDC only (this variant)
Dimmable: Yes
PCB width: 10 mm
Cut length: 50 mm (markings on PCB)
Standard roll length: 5 metres
Custom lengths: Available on request
IP ratings: IP42 (standard), IP65, IP67, IP68 (waterproof variants)
Working temperature: -20°C to +50°C
Cable: 15 cm input cable (custom cable lengths available)
Adhesive: 3M yellow tape standard; 3M red tape optional
Type: Static colour (non-RGB)
Сертификаты: SAA, CE, RoHS
Average lifetime: 50,000 hours
Dotless COB technology
The COB (Chip-on-Board) process places LED chips directly onto the PCB substrate without individual packaging frames, eliminating the gaps between discrete SMD LEDs that create the familiar “dot pattern” on conventional strip lights. The ILED-COB-480 24V 10MM packs 480 COB LED positions per metre into a 10 mm wide PCB, producing a uniform line of light with no visible light points even at close mounting distances.
At 9 W/m and 900 lm/m, this variant delivers slightly lower output than the 10 W/m COB-480 (13923) but operates exclusively on 24VDC — making it compatible with 24V power supplies and controllers without requiring a voltage converter. The 180° beam angle provides wide, even wash illumination ideal for cove and backlighting applications where the light needs to spread across a broad surface.
IP ratings and installation
The ILED-COB-480 24V 10MM is offered in four IP rating variants. The standard IP42 version is suitable for dry indoor environments such as ceiling coves, under-shelf lighting and interior architectural features. The IP65 variant adds a silicone coating that protects against dust and water jets, suitable for covered outdoor use such as soffit lighting and sheltered facades. The IP67 and IP68 variants provide progressive submersion protection — IP67 for temporary immersion and IP68 for continuous submersion — for use in fountains, water features and harsh outdoor environments.
The strip is supplied on 5 metre rolls with a 15 cm input cable pre-attached. It adheres to surfaces using 3M yellow adhesive tape (standard) or 3M red adhesive tape (optional, higher temperature resistance). The flexible PCB can be bent to follow curved contours and cut at the marked 50 mm intervals to achieve custom lengths. Custom roll lengths and cable configurations are available on request. Always verify the cut markings on the PCB before cutting — cutting between marks will disconnect the circuit.
Colour temperature and dimming
The ILED-COB-480 24V 10MM is available in a continuous colour temperature range from 2700K (warm white) to 6000K (cool white), with intermediate options typically available at 3000K, 4000K and 5000K. The CRI >90 rating ensures accurate colour rendering across the full spectrum, making the strip suitable for retail display, gallery accent lighting and food service environments. The strip is dimmable — confirm compatibility with your intended dimmer (TRIAC, 0-10V or DALI) at order time, as not all COB drivers support every dimming protocol. Being a 24VDC-only variant, this model requires a 24VDC driver — it is not compatible with 12VDC systems.
