The ILED-FX-5050 60 is a flexible LED strip built on the SMD 5050 package at 60 LEDs per meter. It is the upper-middle member of the 5050 range: clearly brighter than the 30 and 48 piece strips, but not as dense or wide as the 120 piece version. That makes it the pick when you want a strong, smooth line of light with colour options, without the very high power draw of the densest strip.<\/p>\n
The strip runs on 12VDC or 24VDC, draws 14.4W per meter and puts out about 1,100 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 10mm wide, cuttable in 25mm steps.<\/p>\n
The 5050 is a bigger die than the 3528 and 2835, so each point is brighter and the light reads as smoother with fewer LEDs per meter. At 60 pieces the strip gives a solid, even line at a sensible 14.4W per meter, which is enough for real task and display work while still being easy to feed along a long run.<\/p>\n
In the 5050 range the number of LEDs per meter sets the brightness. The 60 piece here is well above the softer 30 and 48 piece strips, so it reads as genuinely lit rather than a subtle accent. It is not the densest option, the 120 piece runs about twice as bright, but the 60 piece keeps the draw moderate at 14.4W per meter, which is the balance most accent and task projects want.<\/p>\n
You can have this strip in single colours or in multi-colour. The single colours are red, green, blue, yellow, warm white, commercial white and cool white, one colour per piece. The multi-colour options are RGB and RGB plus White, which add colour mixing and a white channel on the same strip. These are static strips, so the colour is set by a controller rather than addressing each LED separately.<\/p>\n
You can have this strip on 12V or 24. A 12V version is simple and pairs with the small transformers used for short cove and cabinet runs. A 24V version drops less voltage down a long line, so it stays even over longer distances. Choose the voltage that fits your supply and the length of the run.<\/p>\n
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.<\/p>\n
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 10mm wide, so check your channel or cove clears that width. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.<\/p>\n
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.<\/p>\n
You will need a power supply at 12VDC or 24VDC, matched to the strip version, sized for your total meters, which the 14.4W per meter figure makes easy to add up. For the RGB and RGB plus White options you also need a compatible controller. For dimming, a compatible LED dimmer is available.<\/p>\n
As a bright 5050 strip it suits cove and ceiling lighting, under-cabinet and display work, TV and furniture backlight, and colour changing decoration. The multi-colour versions are the pick for signage and feature lines. Outdoors the IP65 and above versions handle eaves, facades and garden edges.<\/p>\n
The SMD 5050 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a 24V supply and a properly sized driver the heat stays manageable even in a tight cove.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-FX-5050 60 is a flexible LED strip built on the SMD 5050 package at 60 LEDs per meter. It runs on 12VDC or 24VDC and puts out about 1,100 lumen per meter with a 120 degree beam. It comes in single colours, red, green, blue, yellow and three whites, plus RGB and RGB plus White multi-colour options. Cut it in 25mm steps, stick it down with the 3M yellow tape, and power it from the 15cm input cable. Choose IP20 for dry walls or IP65 to IP68 where it meets water. A 50,000 hour rated life outlasts most installs.<\/p>","protected":false},"featured_media":13969,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[156,158],"product_tag":[296],"class_list":["post-13968","product","type-product","status-publish","has-post-thumbnail","product_cat-smd-led-strip-light","product_cat-strip-and-module-lights","product_tag-tape","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/product\/13968","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/comments?post=13968"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/media\/13969"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/media?parent=13968"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/product_brand?post=13968"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/product_cat?post=13968"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/ru\/wp-json\/wp\/v2\/product_tag?post=13968"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}