Fyrkantig väderbeständig LED-taklampa med väggfäste, IP65, IK10

The ILED-BH-S20W is a square exterior bulkhead light for ceilings and walls where the fixture has to survive weather and the occasional knock. It is the pick for car parks, warehouses, loading bays and utility spaces, places where an ordinary bulkhead ends up cracked. The die-cast aluminium body gives it the structural strength, and the IK10-rated polycarbonate lens is what keeps it whole after things get dropped or wheeled into it.

Why the IK10 matters

IK10 is the highest of the standard IEC 62262 impact ratings, and that is the point of this fixture. Most bulkheads in this size range stop at IK08 or IK09; this one goes to the top of the scale, so the lens shrugs off the hits that would crack a lesser unit. The difference shows up in a car park, where a trolley or a dropped case finds the fixture, or in a warehouse aisle where a forklift swings wide. Spec it where the fixture takes knocks and you want the diffuser to be the last thing you have to think about.

Two outputs, one housing

It is offered at 20W and 30W on the same 300×300×90mm enclosure. The 20W version gives 2200 lumens at 110 lumens per watt, and the 30W steps up the output at the same efficacy. Because the housing and the mounting pattern do not change between the two, you can specify the lower output for a tight corridor and the higher one for a wider bay, and the install is identical. Colour temperature is set at the bench: it is a 3CCT build, so you choose 2800K warm white, 4000K neutral or 6500K cool white before the housing is closed.

Build and mounting

The housing is die-cast aluminium, finished in white or black. The polycarbonate lens is anti-UV, so it does not yellow with age, and it is gasketed to hold the IP65 seal when the fixture is closed. The driver sits inside the body, sealed, so there is no external ballast or power box to mount. It is a surface mount: the back plate carries fixing points for a flat ceiling or wall, and wiring goes direct to the mains through the internal terminal block. It is a Class I fixture, so the circuit needs a protective earth.

Kontroll

The base unit is a standard on/off fixture. It switches with the circuit, a wall switch, a sensor or a timer, and it does not dim. That is deliberate. The control functions are kept on separate SKUs, so where a project wants DALI dimming, motion sensing or a photocell, the wall-packed and emergency variants of the same series carry those, and the two are specified together rather than confused.

Vad finns i förpackningen

Each unit ships as a single fixture with the driver already wired in, the mounting hardware in the box, and the terminal block ready to connect. The anti-UV lens is fitted at the factory and should stay in place after install. Nothing else is packed inside, so it is ready to wire straight to the supply.

Vad du behöver ta med dig

You need the fixings for the ceiling or wall mount and a protected circuit with a protective earth. For an outdoor or wet-location install, check the mounting spot sits within the IP65 zone and that the seal stays closed. A screwdriver and wire strippers cover the job.

Var den används

It is built for the outside of commercial and institutional buildings, or the rough parts of the inside. Car parks and undercrofts take the IK10 lens and the IP65 seal, so the fixture survives vehicle doors, trolleys and rain runoff. Warehouse aisles and storage use it overhead where forklifts swing wide. Loading bays, service corridors and covered walkways use the wide beam and the two outputs to cover both tight and open areas from one product. One SKU also lets a project run a warm white at the entrance and a cooler white at the rear service door.

Certifieringar och garanti

The ILED-BH-S20W carries SAA for Australia and New Zealand, CE for Europe, and RoHS. The warranty runs from three to five years, depending on the region and distributor terms. The sealed body and gasketed lens mean you do not open the unit; a wipe of the diffuser face keeps it looking right.

Varför väljer köparna just dessa framför alternativen? Här är vad vi hör från kunderna:

IK10, the top of the scale. Most bulkheads in this size range stop at IK08 or IK09. This one is rated to the highest standard impact rating, so the lens survives the knocks that would crack a lesser unit.

Die-cast aluminium body. The housing is cast, not stamped. That is what carries the impact rating and keeps heat out of the driver, supporting the 110LM/W output over time.

Two outputs, one housing. The 20W and 30W versions share the same 300×300×90mm enclosure and mounting pattern, so you order the lower output for tight corridors and step up to 30W for wider bays without changing hardware.

3CCT at the bench. Pick warm white, neutral or cool before the housing is closed. One SKU then covers the whole project, and the choice is set at the bench rather than up on a ladder.

SAA, CE and RoHS in one SKU. The SAA approval clears Australia and New Zealand, so a mixed-market project does not need a second, locally approved unit.

The ILED-BH-S20W is a square exterior bulkhead for ceilings and walls where weather and knocks are a daily fact. It is the workhorse of the range, not a sheltered-interior light.

Car parks and undercroft parking. The IK10 lens survives vehicle doors, luggage and trolleys, and the IP65 seal handles rain runoff and washdown. The wide beam keeps bays and driving lanes readable.

Warehouse aisles and storage. Overhead fixtures here get caught by forklifts and shelving. The cast body and IK10 lens absorb hits that would crack a lighter fixture, and the dust seal keeps the output steady.

Outdoor walkways and entry canopies. Covered paths, canopies and porte-cocheres expose the fixture to rain and foot traffic. The IP65 seal and IK10 lens cover both.

Loading bays and service corridors. These mix moisture, dust and impact. The sealed body and gasketed lens keep the inside dry and clean, and the two outputs cover narrow corridors and wider bays from one housing.

Utility rooms and plant areas. Boiler rooms, electrical rooms and mechanical spaces want low-maintenance light that still works after years. The sealed driver and anti-UV lens are aimed at exactly that.

Några saker att kontrollera innan du beställer:

Val av effekt. The 20W version delivers 2200 lumens; the 30W version steps up proportionally at the same 110LM/W. Choose based on illumination level — 20W for narrow corridors and utility areas, 30W for wider car parks and open storage zones.

Färgtemperatur. Three fixed settings are available at installation: 2800K warm white, 4000K neutral and 6500K cool white. Set the switch before closing the diffuser — it cannot be changed after installation.

Finish selection. White and black housing finishes are available. White is standard. Black suits car park ceilings and modern architectural interiors where a lower-visibility fixture is desired.

Monteringssätt. The fixture can be surface-mounted to any flat ceiling or wall, or recessed into a 300×300mm cutout. Confirm the mounting surface supports the fixture weight and that the IP65 seal remains intact after installation.

SAA compliance. If the project requires SAA approval for Australian or New Zealand markets, confirm this variant carries the certification before ordering. The ILED-BH-S20W lists SAA on its specifications table.