LED Vapour Proof Fitting Light IP66 Motion Sensor Emergency DALI2

The LED Vapour Proof Fitting Light combines industrial-grade durability with smart energy control. The M3 series — ILED-TRP-60C M3, ILED-TRP-120C M3, and ILED-TRP-150C M3 — is a single-tube design built for warehouses, parking structures, workshops, and food-processing areas where moisture, dust, and physical impact are everyday concerns. Three frame lengths cover most ceiling layouts: 600 mm (95 × 80 mm cross-section), 1200 mm, and 1500 mm, all sharing the same 95 mm width and 80 mm depth for consistent styling across an installation.

Sizes and output

The three sizes step from 3000 to 9000 lumens across the 20W, 40W and 60W models, all delivering up to 150 lumens per watt. The LEDs are LM80 rated with CRI above 80, so colours appear natural rather than washed-out. Colour temperature is tunable between 2800K (warm white) and 6500K (cool white) via a dip switch inside the driver, letting you match the lighting to the space — warmer tones for rest areas, cooler tones for task-oriented zones. The 120° beam angle spreads light evenly across the floor without hot spots.

The housing is grey PC (polycarbonate), which resists corrosion from cleaning chemicals and humidity better than bare metal. Class II electrical classification means the fixture has double insulation and does not require a separate earth connection, simplifying wiring in retro-fit projects. The driver provides a power factor above 0.9 and flicker-free operation. Input voltage is 220–240VAC 50/60 Hz.

Motion sensor and corridor mode

The built-in motion sensor supports corridor mode: when the area is unoccupied the light drops to a low standby level (typically 10–30 % of full output), then ramps back to full brightness when movement is detected. This cuts energy use in corridors, storage aisles, and car parks where lights are often left on unnecessarily. The sensor detection range, time-out, and lux threshold can be adjusted with a remote controller or set by the installer before hand-over.

Dimming and control options

Three dimming protocols are available: TRIAC (leading-edge), 0-10V analogue, and DALI2 digital. DALI2 is the preferred choice for new builds and major retro-fits because it allows individual fixture addressing, scene setting, and integration with building management systems. The motion sensor and dimming function operate independently — you can run the sensor in on/off mode without dimming, or combine DALI2 dimming with sensor control for maximum energy savings.

Emergency variant

An emergency version is offered alongside the standard and dimmable models. The emergency driver provides 3 hours of backup illumination at reduced wattage, suitable for exit routes, corridors, and stairwells that require certified escape lighting. Self-testing versions are available on request, allowing facility managers to verify battery health automatically without manual intervention.

Montering och installation

The M3 uses a buckle-lock end-box design: the end caps click into the main body and seal the joint, maintaining the IP65 rating while making field wiring straightforward. Cables enter through the end boxes. The fixture can be surface-mounted to a ceiling or suspended from wires or chains. For concrete or brick ceilings a direct surface-mount bracket is used; for suspended ceilings the fixture hangs from the structural grid or from eye-bolts fixed into the slab above.

Var den används

Use the M3 in the damp, wash-down spaces a standard fitting will not survive: warehouse and storage aisles, car parks and ramp lighting, food, dairy, and chemical processing floors, laundries, and plant rooms. The 600 mm, 1200 mm, and 1500 mm lengths match typical corridor bays, so most layouts line up without a custom cut. Where the ceiling is concrete or brick, surface-mount it; where it is a suspended ceiling, hang it from the grid. The single 95 mm wide, 80 mm deep tube keeps the line clean and consistent across a row.

Livslängd och tillförlitlighet

The LM80 LED source, a power factor above 0.9, and the Class II double insulation are the parts that keep the M3 running for years, and the supplier backs the fixture with a 5-year warranty. The IP65 PC housing seals the joints against dust and water jets, which is what protects the driver in a wash-down area. Because it is Class II there is no separate earth to worry about, and the driver runs flicker-free, so it sits well under CCTV. Keep the end boxes tight and the tube out of direct impact and the line will hold up.

Certifications and warranty

The M3 series carries CE, RoHS, SAA, and TUV certifications, covering compliance for European, UK, Australian, and international markets. The supplier backs the fixture with a 5-year warranty, reflecting confidence in the LED source and driver longevity under normal operating conditions.

Why do buyers pick the ILED-TPR-C M3 over other vapour-proof battens? Here is what we hear from customers:

Built-in motion sensor with corridor mode. The integrated sensor drops the light to a low standby level when the area is empty and restores full brightness on detection. In corridors and storage aisles this cuts energy use without sacrificing safety.

150LM/W output. At 150 lumens per watt the M3 out-performs many similarly priced vapour-proof lights that sit around 120–130LM/W. Fewer fixtures are needed to reach the target illuminance, lowering both material and installation costs.

DALI2, 0-10V, and TRIAC dimming all available. Whether your BMS speaks DALI2, analogue 0-10V, or TRIAC, there is an M3 variant that plugs in directly. No adapters required.

IP65 sealed body with Class II construction. The PC housing and buckle-lock end boxes keep dust and water jets out. Double insulation means no earth wire is needed, which speeds up wiring.

5-year warranty. Most rivals in this category offer 2–3 years. The longer period reflects confidence in the LED source and driver quality.

Warehouses and distribution centres. — High ceilings and long aisles benefit from the 120° beam spread and corridor-mode sensor, which cuts energy in low-traffic storage zones while keeping main walkways fully lit.

Parking garages and car parks. — IP65 sealing handles damp, poorly ventilated conditions. The motion sensor dims lights in empty bays and ramps up when a car enters, reducing standby consumption dramatically.

Workshops and light-industry spaces. — The PC housing resists chemical splashes and routine wash-down. Class II construction removes the need for an earth wire, speeding up retro-fit installations in existing buildings.

Food-processing and cold-storage areas. — Moisture-resistant PC body and IP65 sealing withstand humid environments and periodic cleaning. The sealed end boxes prevent condensation ingress that can degrade cheaper fixtures.

Corridors and circulation spaces. — Corridor-mode sensor is ideal here: lights stay at a low standby level and brighten only when someone passes, delivering the biggest energy savings per fixture.

Retail back-of-house and stockrooms. — CRI above 80 renders product colours accurately for quality-check tasks. The three selectable CCTs let managers tune the ambiance between a bright working environment and a warmer rest-area setting.

Hotels and hospitality service areas. — Staff corridors, laundry rooms, and storage cupboards use the same fixture with corridor-mode sensors to keep energy costs down in spaces that are occupied intermittently.

Stock management. — One M3 SKU covers 600 mm, 1200 mm, and 1500 mm lengths with the same 95 × 80 mm profile. Specifying all three sizes together simplifies reordering and reduces SKUs your warehouse holds.

Voltage compatibility. — The M3 accepts 220–240VAC 50/60 Hz. If your project is in a 110V region (North America, parts of South America and Japan), confirm the driver variant with your sales contact before ordering — the standard M3 driver is not rated for 110V input.

DALI2 vs 0-10V selection. — Choose DALI2 if you need individual fixture addressing, scene recall, or BMS integration. Choose 0-10V for simple single-zone dimming. The basic non-dimmable version is sufficient for spaces that only need on/off control.

Emergency version availability. — Not all M3 variants include the 3-hour emergency driver. Specify “emergency” or “self-test” when ordering if your project requires certified escape lighting.

IK rating note. — The M3 spec table does not list an IK impact rating. If impact resistance is a project requirement, ask about the M6 variant, which carries an IK10 rating, or confirm the M3 IK rating before placing the order.