The ILED-DM2 C is a 3-channel RGB controller and dimmer for LED strip work. It runs three channels, red, green and blue, which is what an RGB strip needs, and it drives up to three zones of strip from the one unit. It is controlled by a 2.4G RF remote, so you set the colour and the level from where you stand. It is the pick for an RGB strip where you want to mix the colour and run it as a few separate zones.<\/p>\n
The unit drives three channels, red, green and blue, and mixes them to make any colour. It runs up to three zones of strip, so you can split a run into three separately controlled sections, and each section takes its own colour and level from the remote. That is the point of it, because a colour strip across a room or a facade is easier to manage in zones than as one long run.<\/p>\n
The controller takes a 12 to 24V DC supply and gives three channels at 4A each, so the maximum load is 144W at 12V and 288W at 24V. The dimming runs from 0 to 100 percent, and the remote works over RF at 2.4GHz. Power comes in on a DC2.1 or a screw terminal. The receiver is 85 by 45 by 23mm at 45g, and the remote is 150 by 40 by 13mm at 60g. It works from -30 to 55 degrees.<\/p>\n
The three channels are red, green and blue, which is the RGB colour, so the strip mixes to any colour you pick. This is a colour-only control, with no dedicated white channel, so if you want a plain white on the same strip, that is the RGBW or the RGB+CCT version. For a colour strip, the three channels are all you need.<\/p>\n
The controller runs three zones, so you can address three separate runs of strip, or three sections of one run, from the one unit. Each zone takes its own colour and its own level, so a facade or a long cove can move in three parts instead of all at once. It is the way to keep a long strip manageable, because you set the zones from the remote.<\/p>\n
The dimmer runs 0 to 100 percent on each channel, so you set the level of each colour to taste. Mix red, green and blue to make a colour, and the dimmer holds it there, so a red, a green or a mix of the three stays steady. The dimming is flicker-free, so the colour does not pulse as you change it.<\/p>\n
The control is a 2.4G RF remote, so it changes the colour and the level without a cable between the two, which is what you want for a cove or a display. It comes as a 2.4G version and a push-button version, so you pick wireless or a panel.<\/p>\n
The supply comes in on a DC2.1 plug or a screw terminal, so you wire it the way the rest of the install is run. The three channels go out to the strip, one per channel, and you match the red, green and blue leads to the three outputs. Keep the wiring clean and the strip the right voltage.<\/p>\n
Each set ships as the receiver and the remote, with the DC2.1 and the screw terminal on the receiver and the 2.4G or push-button remote to control it. You wire the supply and the three channels on your end, and keep the remote to hand to change the colour and the level.<\/p>\n
You will need a DC supply at 12V or 24V, matched to the strip, sized for the total load on the controller, which is up to 144W at 12V or 288W at 24V. You also need the RGB strip it is driving, and you match the three channels to the strip leads.<\/p>\n
Because it drives an RGB strip with a wireless remote, it shows up in home accent lighting, coves and feature lines, shop and display lighting, and anywhere you want to change the colour from where you stand. It is the pick where you want the colour to move on command, and the three zones let one controller run three runs of strip at once.<\/p>\n
It carries up to 144W at 12V or 288W at 24V, so it drives a real load, and the flicker-free dimming is what keeps the colour steady at every level. It is rated to work from -30 to 55 degrees, and the 45g receiver is small enough to drop into the install.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-DM2 C is a 3-channel RGB controller and dimmer for RGB LED strips, run by a 2.4G RF remote. It takes a 12 to 24V DC supply and gives three 4A channels, so it carries up to 144W at 12V or 288W at 24V. The three channels drive red, green and blue, so you mix any colour from a single strip, and the remote runs three separately controlled zones. You dim from 0 to 100 percent, with flicker-free dimming. It connects with a DC2.1 or a screw terminal, and the small remote is the part you keep to hand.<\/p>","protected":false},"featured_media":13782,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[240,158],"product_tag":[300,308],"class_list":["post-13777","product","type-product","status-publish","has-post-thumbnail","product_cat-dimmer-and-controller","product_cat-strip-and-module-lights","product_tag-2-4g","product_tag-rgb","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product\/13777","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/comments?post=13777"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media\/13782"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media?parent=13777"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_brand?post=13777"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_cat?post=13777"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_tag?post=13777"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}