The ILED-DM3 H is a wall-mounted touch dimmer for LED strip lights. It is a small panel you set into a wall, and you dim the strip by touching it, so there is no remote to keep and no switch to guess at. It runs three channels, each at 4A, which is what you need for a multi-zone strip or a strip that needs more than one level of control. It is the pick for a cove, a cove line or a room where you want to set the light with a hand on the wall rather than with a remote on the table.<\/p>\n
The unit sits on the wall and runs up to three dimmable channels of LED strip, so you control the level from where you stand, by touch. It dims each channel from 0 to 100 percent, and the dimming is flicker-free, which is what you want on a strip that sits in view. It is the control point for the strip, so you set the level and leave it, rather than hunting for a remote or a switch.<\/p>\n
The panel takes a 12 to 24V DC supply and gives three channels at 4A each, so the maximum load is 144W at 12V and 288W at 24V. The dimming runs from 0 to 100 percent, and it connects with a DC2.1 or a screw terminal. The panel is 86 by 84 by 60mm at 100g, which is what the 84 panel size refers to, and it works from -30 to 55 degrees.<\/p>\n
The panel runs three channels, each at 4A, so you can drive up to three zones of strip, or a strip that uses more than one channel, from one panel. If you are running a multi-zone cove, each zone gets a channel and a level of its own, and if you are running a single long strip, you split it across the channels so the panel can control the sections. Work the load against 144W at 12V or 288W at 24V, so each channel stays under its 4A.<\/p>\n
You set the level by touching the panel, which is cleaner than a slider and quicker than a remote. The dimming is flicker-free, so the light does not pulse or shimmer as you change the level, which is the difference between a strip that sits still and one that twitches. It matters most on a strip that is in view, where a flicker is what people notice first.<\/p>\n
This is a wall-mounted panel, so it stays where you set it, instead of going in a pocket or on a table. That is the point of it, because a cove or a room is lit from the wall, not from somewhere you have to carry. You set the level at the panel and walk away, and the light stays where you left it.<\/p>\n
The supply comes in on a DC2.1 plug or a screw terminal, so you wire it the way the rest of the install is already run. The three channels go out to the strip, one per channel, and you match the leads to the outputs. Keep the wiring clean and the strip the right voltage, and the panel runs it.<\/p>\n
Each unit ships as the panel, with the DC2.1 and the screw terminal on the back. You set it into the wall, wire the supply and the three channels, and it is the point where you set the level of the strip.<\/p>\n
You will need a DC supply at 12V or 24V, matched to the strip, sized for the total load on the panel, which is up to 144W at 12V or 288W at 24V. You also need the strip it is driving, and you match the three channels to the strip leads.<\/p>\n
Because it is a wall touch dimmer, it shows up in bedrooms and living rooms, in coves and under-cabinet lines, and in commercial spaces where you want to set the light from the wall. It is the pick where you want to dim the strip by hand and keep the control at the point where you stand.<\/p>\n
It draws up to 144W at 12V or 288W at 24V, so it carries a real load, and the flicker-free dimming is what keeps the light steady at every level. It is rated to work from -30 to 55 degrees, which covers a normal indoor space, and the 84mm panel is small enough to sit on the wall without crowding it.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-DM3 H is a wall-mounted touch dimmer panel for LED strip lights. It is a compact 84mm panel with three 4A channels, so it dims up to three zones of strip from 12 to 24V, to 144W at 12V or 288W at 24V. You set the level by touching the panel, from 0 to 100 percent, with flicker-free dimming. It connects with a DC2.1 or a screw terminal, which keeps the wiring simple, and it runs SMD and COB strips. It sits on the wall where you reach it, replacing a light switch for the strip it runs.<\/p>","protected":false},"featured_media":13822,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[240,158],"product_tag":[],"class_list":["post-13818","product","type-product","status-publish","has-post-thumbnail","product_cat-dimmer-and-controller","product_cat-strip-and-module-lights","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product\/13818","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/comments?post=13818"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media\/13822"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media?parent=13818"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_brand?post=13818"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_cat?post=13818"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_tag?post=13818"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}