The ILED-FX-3528 120 is a flexible LED strip built around the SMD 3528 package at 120 LEDs per meter in a single row. It is the higher-output member of the standard, single-row 3528 range: clearly brighter than the 30 and 60 piece strips, but not as dense as the double-row 240D. That middle position makes it the pick when you want a strong, smooth line of light without the width and power of the double-row version.<\/p>\n
The strip runs on 12VDC or 24VDC, draws 9.6W per meter and puts out about 700 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 8mm wide, cuttable in 25mm steps.<\/p>\n
Doubling the density of the 60 piece strip nearly doubles the output, so the light looks smoother and brighter, with less visible spacing between the points. It suits bright coves, task lighting and display work where you want more than a soft accent. It stays in a single row, so it keeps the narrow 8mm body of the standard strip rather than widening out like the double-row 240D.<\/p>\n
You can have this strip on 12V or 24. A 12V version is simple and pairs with the small transformers used for short cove and cabinet runs. A 24V version drops less voltage down a long line, so it stays even over longer distances, which is why 24 is the pick for long corridors and bigger rooms. Choose the voltage that fits your supply and the length of the run.<\/p>\n
This is a static strip, so each piece is one single colour. You pick one of the seven available colours before ordering: red, green, blue, yellow, warm white, commercial white or cool white. The white options cover three temperatures, so warm white suits living spaces while cool white is cleaner for work areas. For accent or signage the red, green, blue and yellow single colours are the ones to use.<\/p>\n
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.<\/p>\n
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug. At 8mm wide it disappears into most coves and channels.<\/p>\n
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.<\/p>\n
You will need a power supply at 12VDC or 24VDC, matched to the strip version, sized for your total meters, which the 9.6W per meter figure makes easy to add up. For dimming, a compatible LED dimmer is available. If you are not hard-wiring, use an adapter or driver that matches the strip voltage.<\/p>\n
As a bright single-row strip it suits cove and ceiling lighting, under-cabinet and display work, task lighting, and picture lighting. Outdoors the IP65 and above versions handle eaves, facades and garden edges. The single colours also make it useful for signage and feature lines.<\/p>\n
The SMD 3528 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a 24V supply and a properly sized driver the heat stays manageable even in a tight cove.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-FX-3528 120 is a high-density flexible LED strip with 120 SMD 3528 LEDs per meter in a single row. It runs on 12VDC or 24VDC and puts out about 700 lumen per meter with a 120 degree beam. Each strip is a static single colour, from red, green, blue, yellow, warm white, commercial white or cool white. Cut it in 25mm steps, stick it down with the 3M yellow tape, and power it from the 15cm input cable. Choose IP20 for dry walls or IP65 to IP68 where it meets water. Its 50,000 hour rated life outlasts most installs.<\/p>","protected":false},"featured_media":14000,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[156,158],"product_tag":[296],"class_list":["post-13995","product","type-product","status-publish","has-post-thumbnail","product_cat-smd-led-strip-light","product_cat-strip-and-module-lights","product_tag-tape","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product\/13995","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/comments?post=13995"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media\/14000"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/media?parent=13995"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_brand?post=13995"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_cat?post=13995"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/sv\/wp-json\/wp\/v2\/product_tag?post=13995"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}