The ILED-FX-5050 30 is a flexible LED strip built on the SMD 5050 package, the largest of the common strip LEDs, laid out at 30 LEDs per meter. It is the entry-density member of the 5050 range, but because each LED is bigger than those on the 3528 and 2835 strips, it still gives a solid, even line of light at low power. That combination makes it a good first choice when you want 5050 output without the very high brightness of the denser 48, 60 and 120 piece versions.<\/p>\n
The strip runs on 12VDC or 24VDC, draws 7.2W per meter and puts out about 600 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 10mm wide, cuttable in 25mm steps.<\/p>\n
The 5050 is a bigger die than the 3528 and 2835, so each point is brighter and the light reads as smoother with fewer LEDs per meter. At 30 pieces the strip keeps the power draw modest at 7.2W per meter, which is friendly for long runs and easy to feed. It is not the brightest 5050 you can buy, it is the low-density, economical one.<\/p>\n
You can have this strip in single colours or in multi-colour. The single colours are red, green, blue, yellow, warm white, commercial white and cool white, one colour per piece. The multi-colour options are RGB and RGB plus White, which add colour mixing and a white channel on the same strip. These are static strips, so the colour is set by a controller or driver rather than addressing each LED separately, which keeps the system simple.<\/p>\n
You can have it on 12V or 24. A 12V version pairs with the small transformers used for short cove and cabinet runs. A 24V version drops less voltage down a long line, so it stays even over longer distances. Choose the voltage that fits your supply and the length of the run.<\/p>\n
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.<\/p>\n
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 10mm wide, a touch broader than the 8mm 3528 strips, so check your channel clears that width. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.<\/p>\n
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.<\/p>\n
You will need a power supply at 12VDC or 24VDC, matched to the strip version, sized for your total meters, which the 7.2W per meter figure makes easy to add up. For the RGB and RGB plus White options you also need a compatible controller. For dimming, a compatible LED dimmer is available.<\/p>\n
As an economical 5050 strip it suits cove and ceiling lighting, under-cabinet work, TV and furniture backlight, and general accent lines. The multi-colour versions are the pick for colour changing decoration and signage. Outdoors the IP65 and above versions handle eaves, facades and garden edges.<\/p>\n
The SMD 5050 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a 24V supply and a properly sized driver the heat stays manageable even in a tight cove.<\/p>","protected":false},"excerpt":{"rendered":"
The ILED-FX-5050 30 is a flexible LED strip built on the SMD 5050 package at 30 LEDs per meter. It runs on 12VDC or 24VDC and puts out about 600 lumen per meter with a 120 degree beam. It comes in single colours, red, green, blue, yellow and three whites, plus RGB and RGB plus White multi-colour options. Cut it in 25mm steps, stick it down with 3M yellow tape and power it from a 15cm input cable. Choose IP20 for dry walls, or IP65 to IP68 where it meets water. Its 50,000 hour rated life outlasts most installs.<\/p>","protected":false},"featured_media":13990,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false},"product_brand":[],"product_cat":[156,158],"product_tag":[296],"class_list":["post-13989","product","type-product","status-publish","has-post-thumbnail","product_cat-smd-led-strip-light","product_cat-strip-and-module-lights","product_tag-tape","first","instock","shipping-taxable","product-type-simple"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/product\/13989","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/comments?post=13989"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/media\/13990"}],"wp:attachment":[{"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/media?parent=13989"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/product_brand?post=13989"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/product_cat?post=13989"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.iled-lights.com\/zh\/wp-json\/wp\/v2\/product_tag?post=13989"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}