LED Underground Light Four Sides Lighting Round IP67 Stainless Steel

What it does

The ILED-IG1-4 D is a four-side LED underground light you set into the ground or embed in a low wall, so it throws light out on all four faces of its body at once. Instead of pointing one direction, it lights around the whole unit, so it suits a central feature, tree, or island where you want light on every side. It is a low-voltage 12V or 24V unit, so it suits outdoor and damp locations.

Four sizes

The family runs in four bodies. ILED-IG1 D is the smallest at φ42mm, 1W. ILED-IG2 D is φ52mm, 1W. ILED-IG3 D is φ62mm, 1 to 3W. ILED-IG4 D is the largest at φ75mm, 1 to 3W. All four are four-side lighting on a 30° beam. The smaller two suit a tree trunk or a tight feature; the larger two cover a wider central spot. Each has its own cut-hole, so match the size to the opening you cut.

Four sides, 30° beam

Every unit throws to all four faces of the body, which is the whole point of the D version. A 30° beam on each face gives four defined washes, so the light comes around the unit rather than off one edge. That reads as a glow around a tree, a post, or a central walkway island. If you only need one side, that is the A model, and for two sides it is the B model. Here one fixture lights all four, so the area around it stays even and you use fewer units.

Colour and temperature

Choose a single white from the 2800K to 6500K range, or pick red, green, or blue. The white covers a warm to cool range, so you match the tone to the space. The coloured versions are for marking out a central feature or a walkway island. The LED source is a high-power chip, and the output is 85 to 90 lumens per watt, so a 3W unit gives a strong four-sided glow for its size.

Power: 12V or 24V, DC or AC

The input is 12V or 24V, and it is available on DC or AC, so it fits both the low-voltage DC runs and the AC outdoor circuits. Keep the supply dry and out of the wet area. Size the supply to the load on the line. Because it is low voltage, it is the safe choice for a place you walk or stand near.

Fabricación y materiales

The body is 304 stainless steel and the face is tempered glass. That is the combination that lets it sit in the ground, take foot traffic, and still clear years of weather without corroding. The stainless holds its finish, and the tempered glass spreads the light to all four sides and shields the source. It is a small, sealed unit.

IP67 o IP68

The unit is rated IP67, with an IP68 option. IP67 is sealed against dust and against temporary immersion, which covers spray, rain, and a brief flood. IP68 is the deeper-immersion rating for the locations that sit underwater for longer. Pick the rating to the site. The cuthole and body stay tight, so the joint does not open.

Instalación

Each size has a set cut-hole: φ40mm for the φ42 body, φ46mm for the φ52 body, φ56mm for the φ62 body, and φ64mm for the φ75 body. Cut the opening in the ground, deck, or wall to that diameter, set the unit in, and it throws to all four sides. Wire the low-voltage supply. The body is shallow, so it seats flush with a finished surface.

Dónde se utiliza

Use the ILED-IG1-4 D around the features you want to glow on every side: tree trunks, central walkway islands, sculpture bases, circular planters, and the middle of a wide border. Because it throws to four faces on a 30° beam, the area around it stays even and you need fewer units than a row of single-side lights. Where you only need one side, that is the A model; for two sides, the B model. The IP67 or IP68 body is what suits the outdoor, wet spot.

Lo que debes aportar

A 12V or 24V power supply sized to the load on the line. The cut-tool for the hole your size specifies. The unit, its body, and the faces are all in the box. Keep the supply dry and the area will hold up.

Vida útil y fiabilidad

The high-power chip, the 304 stainless steel, and the tempered glass are the parts that keep it going, and the supplier backs it with a 2-year warranty. It is sealed, has no moving parts, and runs on a low-voltage supply, so the failure points are few. Keep the faces out of a direct impact. It is CE and RoHS certified.

Why choose the ILED-IG1-4 D.

It is the four-side inground light, in four sizes from φ42mm to φ75mm, so one fixture glows around a feature instead of lighting one edge. The 30° beam on each face and the 85 to 90 LM/W output give four crisp washes, which keeps the area around a tree, island, or central walkway even. The body is 304 stainless steel with tempered glass, rated IP67 with an IP68 option, on a safe 12V or 24V input, DC or AC. Colour is a white from 2800K to 6500K, or red, green, or blue. Each size has its own cut-hole, so the install lines up. It is CE and RoHS certified with a 2-year warranty. It glows around the feature rather than off one edge, so the area stays even, and it is the most even of the three throws. If the job is light around a central feature on all sides, this is the fixture.

What is the difference between the A, B, and D models?

They differ only in how many sides they throw to. The A is single-side, so you point it at one direction. The B is two-side, lighting both faces of a line. The D, this one, throws to all four sides of the body, so it lights around a central feature. The four sizes, from φ42mm to φ75mm, and the cut-holes are the same across all three. Pick the throw to the job.

How do I choose which size?

Match the body to the opening you will cut and the feature you are lighting. ILED-IG1 D at φ42mm and ILED-IG2 D at φ52mm are 1W, for a tree trunk or a tight feature. ILED-IG3 D at φ62mm and ILED-IG4 D at φ75mm run 1 to 3W, so they give a brighter four-sided glow for a larger central spot. The cut-holes are φ40mm, φ46mm, φ56mm, and φ64mm, so measure the opening first.

What is the difference between IP67 and IP68?

IP67 is sealed against dust and against temporary immersion, which covers spray, rain, and a brief flood. IP68 is the deeper-immersion rating for a spot that sits underwater for longer. For most tree, deck, and border work, IP67 is enough. Pick IP68 for the pool-adjacent and permanently wet locations. Both are the same four-side body and the same 30° beam.

Does it run on DC or AC?

Both. The input is 12V or 24V on DC or on AC, so it fits a low-voltage DC run or an AC outdoor circuit. Pick the one that matches the supply you are already running to the site. The fixture is low voltage, so it is safe to install where people walk or stand. The supply should stay dry, though, since the fixture is the waterproof part.

What colours can I get?

A single white from the 2800K to 6500K range, or red, green, or blue. The white covers a warm to cool range, so you match the tone to the space. The colours are for marking out a central feature or a walkway island. The 30° beam keeps whichever you pick as four clean, directional lines around the unit.

Put the ILED-IG1-4 D around the features you want to glow on every side: tree trunks, central walkway islands, sculpture bases, circular planters, and the middle of a wide border. Because it throws to four faces on a 30° beam, the area around it stays even and you need fewer units than a row of single-side lights. The four sizes, from φ42mm to φ75mm, let the smaller two hug a tree trunk and the larger two cover a bigger central spot. The 85 to 90 LM/W output keeps all four lines crisp. A 12V or 24V input, DC or AC, keeps it safe in the damp location. Choose IP67 for most outdoor work and IP68 for the permanently wet spots. For a tree line, place one around each trunk and the four-sided throw covers the base evenly. For a central island in a wide path, run several around the edge and the middle stays lit from every direction. For a sculpture or a planter, the glow keeps it visible at night without hotspots. If you only need one side, that is the A model, and for two sides the B model.

Check these before you buy the ILED-IG1-4 D. The four sizes run from ILED-IG1 D at φ42mm, 1W, up to ILED-IG4 D at φ75mm, 1 to 3W, and each has a set cut-hole from φ40mm to φ64mm, so measure the opening first. It is four-side lighting on a 30° beam, 85 to 90 LM/W, in 2800K to 6500K white or red, green, and blue. The body is 304 stainless steel with tempered glass, rated IP67 with an IP68 option, on a 12V or 24V input, DC or AC. It ships in a carton of 100 pieces at 0.16kg each, a 36 x 36 x 48cm carton weighing 15.6kg gross. A power supply is not included. The small sealed body and the low-voltage input are what suit the wet, outdoor spot. The D shares the same four sizes and cut-holes as the family’s A and B, so pick the throw to the job. If the job is light around a central feature on all sides, this is the fixture.