CCT Dual Color Controller Dimmer with 2.4G Remoter 3 Zone ILED-DM2 B

What it does

The ILED-DM2 B is a 3-zone CCT dual color dimmer controller for 12V and 24V strips. Three zones mix warm and cool white on their own, so each zone can set both the color temperature and the brightness. It is driven by a 2.4G remote and a push button on the body. There is no pair code and no app. It suits shops, offices, and homes where you want one zone warm and another cool.

2 channels, 3 zones

Two channels: one warm white and one cool white. Mix them and each zone shifts color temperature between a warm white and a cool white. Three zones lets you put a different mix and a different brightness in three rooms: a warm reading nook at 60%, a neutral office at 90%, and a cool display case at 100. Each of the two channels is 6A, so the zones have headroom. The 2-channel layout suits a house where each room wants its own temperature.

How it works

The 2.4G remote sends over radio, not over cables. Each channel has its own address, so the three zones fade and tint independently. The remote is RF 2.4GHz, so no line of sight is needed. The receiver and remote keep their settings when the power goes off. The push button on the body does the same jobs as the remote. There is no pairing step: power it up and it runs.

Output and dimming

Each of the two channels is rated at 6A, so the controller drives up to 144W on a 12V system or 288W on a 24V system. The CCT mix moves between a warm white and a cool white, and dimming runs 0 to 100%. The fade and the tint are both smooth. The output is a DC2.1 plus a screw terminal. For a long strip, run a separate 12V or 24V power supply to the strip and use this for the signal.

Power and connection

Feed the controller from a DC2.1 plug or the screw terminal. It runs on a 12V to 24V DC supply. Use a matching power supply sized to the strip, a few volts above for the long runs. Do not exceed 6A on a channel. For 3 zones, wire the two channels (warm and cool white) of each zone and share the common ground.

Receiver and remote

The receiver measures L85 by W45 by H23mm and weighs 45g. The remote measures L150 by W40 by H13mm and weighs 60g. The remote holds the three zones, the warm-cool mix, and the dimming. It bolts the receiver to a wall. Both carry their settings across a power cut. The packaging ships in a colorful box or skin pack, and OEM is supported.

Temperature and use sites

It is rated from -30C to +55C, which covers most indoor and sheltered outdoor use. For an outdoor install, mount it under a canopy where the sun does not hit it directly. The 2.4G signal needs a clear path or a short cable, not a wall between the remote and the receiver. The flicker-free output suits camera work, product photos, and retail displays. Use it where dimming plus a warm-cool mix is the whole job.

CCT mix vs single color

The CCT dual color lets each zone shift temperature, not just brightness. That is worth it for a reading nook that wants warm and an office that wants cool in the same house. A single color model like the ILED-DM2 A is cheaper and enough where one color is all you need. For color, the ILED-DM2 D or the ILED-DM2 E. This one is the warm-cool dimmer.

What is in the box

Each order ships one ILED-DM2 B receiver and one 2.4G remote, in a colorful box or skin pack. It has a DC2.1 input and screw terminals for 2 channels, plus 3 push buttons for local control. No cables, connectors, or power supply are included. Add a 12V or 24V supply and a CCT strip.

What you need to supply

A 12V or 24V power supply sized to the strip. A CCT dual color strip within the 6A per channel limit. A mount for the receiver, and a clear path or a short cable for the remote. The remote battery comes with the unit. Everything else is in the box. Do not exceed 6A per channel.

Where it gets used

Use the ILED-DM2 B on retail, office, and display strips, kitchen and under-cabinet lines, and home reading nooks. Its 3-zone CCT layout puts a warm mix in one room and a cool mix in another. For RGB, move to a sibling model.

Why choose the ILED-DM2 B.

Three zones of CCT dual color, two channels at 6A each, so every zone mixes warm and cool white on its own and sets its own brightness. That covers a reading nook that wants a warm mix, an office that wants a cool one, and a display case that wants a neutral one, all in the same house. The 2.4G remote fades and tints the three zones independently with no pair code and no app, and the push button on the body covers the same jobs if the remote goes missing. The output draws a steady 0 to 100%, holds a clean 10% without flicker, and does not shimmer on camera. It is small, 45g, and bolts to a wall or desk, and it works from -30 to +55C. It ships in a colorful box or skin pack, and OEM packaging is supported. A matching power supply is not in the box. If you want a warm-cool mix across three rooms, this is the controller, and it is the mid step between the single color ILED-DM2 A and the RGBW models.

What does the CCT dual color do that a single color dimmer does not?

It mixes a warm white and a cool white, so each zone can shift color temperature between a warm white and a cool white and set its own brightness. A single color dimmer like the ILED-DM2 A only fades one color. Use this one where a reading nook wants warm and the office wants cool in the same house. The 3 zones let all three differ, and the two 6A channels give headroom for the mix. Where you need red, green, and blue, an RGBW model is the better fit.

Will it flicker at low brightness?

No. The output is rated flicker-free and the fade is smooth across 0 to 100%. Even a 10% hold is clean, with no shimmer that shows up in some cheap dimmers. Use it for camera work, product photography, and storefront window lighting. If you dim a long strip, keep the power supply close so the last section holds its level. The clean tint at a low level is what makes it work for a display case that is photographed or filmed.

How much current does each channel carry?

Each of the two channels, warm and cool white, is rated at 6A. Together they drive up to 144W at 12V or 288W at 24V. Do not exceed 6A on one channel; split a long strip across it. The 3-zone layout reuses the two channel addresses, so each zone runs its own warm and cool mix on the same two channels. Size the power supply to the strip and keep it under 6A per channel.

Do I need to pair the remote?

No. It is RF 2.4GHz and talks to the receiver directly, no code entry and no app. The settings survive a power cut, so the controller is not reset when the breaker trips. Use the push button on the body if the remote is lost. The remote keeps its last mix and dimming across a power cut. The remote is L150 x W40 x H13mm, 60g, and the receiver is L85 x W45 x H23mm, 45g.

Put the ILED-DM2 B on retail, office, and display strips, kitchen and under-cabinet lines, and home reading nooks. Its 3-zone CCT layout lets one room hold a warm mix and another a cool mix, each at its own brightness: a reading corner warm at 60%, an office neutral at 90%, and a display case cool at 100. The flicker-free fade and the tint work together for product photography and camera work, where a clean low level matters. For an under-cabinet line, set the mix to taste and leave it. It is not an RGB controller, so where you need red, green, and blue, use the ILED-DM2 D or the ILED-DM2 E. Where you only need one color, use the ILED-DM2 A. This one is the warm-cool dimmer with three zones that each set temperature and brightness. A reading corner holds a warm mix at 60%, the office a neutral 90%, and the display case a cool 100, and the 2.4G remote sets each one and holds it. For a corridor that wants a constant level, lock it in place. Set each mix once and the remote keeps it through the day, so the staff does not re-tune the strips during a busy period.

Buy the ILED-DM2 B in its 3-zone CCT dual color form: 6A per channel, 2 channels (warm plus cool white), up to 144W at 12V or 288W at 24V, 0 to 100% dimming, a warm-to-cool mix, an RF 2.4G remote plus 3 push buttons, and a -30 to +55C rating. The receiver is L85 x W45 x H23mm and weighs 45g, and the remote is L150 x W40 x H13mm and weighs 60g. It ships in a colorful box or skin pack, and OEM packaging is supported. A matching 12V or 24V power supply is not included, so size one to the strip and keep it under 6A per channel. For a single color dimmer in the same 3-zone form, move to the ILED-DM2 A. For RGBW, move to the ILED-DM2 D. For 5-zone RGB+CCT, move to the ILED-DM2 E. This one is the three-zone warm-cool dimmer. Set each mix once and the remote holds it.