RGB RGBW SPI LED Downlights Recessed

The ILED-CL-A C10 is a recessed SPI LED downlight with RGB or RGBW COB output. It is a color fixture first: the SPI control changes colors and effects through a controller, and the same unit works in a Madrix System. Each housing carries a 20cm input cable and a 20cm output cable, so a run of fixtures can be chained without extra boxes in the ceiling.

Models

Three models cover the range:

• ILED-CL2-A C10 7W: 400 lm, body 64mm diameter by 59mm deep, cutout 55mm
• ILED-CL3-A C10 12W: 600 lm, body 85mm diameter by 95mm deep, cutout 75mm
• ILED-CL4-A C10 18W (20W): 1200 lm, body 105mm diameter by 100mm deep, cutout 95mm

The 18W model is listed at 20W in the spec table. Each step up adds output and opening size, so the cutout should be chosen against the ceiling plan. The 7W model suits a small accent; the 18W model covers a larger area or a higher ceiling.

Color and optics

The source is an RGB or RGBW COB. RGBW adds a white channel, which gives pastel tones and a clean white in addition to the RGB colors, so the same fixture works as a color light and a white light. Lenses are fixed at order in 15°, 24°, or 38°. The 15° optic is a tight spot; the 24° suits general display lighting; the 38° spreads widest. The lens cannot be swapped after delivery, so it should be decided against the ceiling plan.

Kawalan

The fixture uses SPI control and is compatible with a Madrix System. SPI runs on a clocked data signal, so fixtures in a chain respond in sync with the controller. The 20cm input and output cables allow one unit to feed the next. Controller and power supply are chosen by the installer; they are not part of the fixture, so the system cost sits outside the downlights themselves.

Construction

The housing is aluminum with a PC component. The IP42 rating covers dry indoor rooms. The fixture recesses into a plasterboard ceiling, and the round body sits flush against the board. The aluminum body also carries heat away from the COB source, which keeps the driver and LED within working range in enclosed ceilings.

Kuasa

Input is DC24V or DC12V, so the fixture needs a matching power supply rather than a mains connection. The supply size depends on the number of fixtures on the run. Confirm the voltage with the order, because the driver input must match the supply.

Installation

Cut a round opening to the cutout size for the model, feed the input cable, wire the chain, then seat the housing. Connect the output cable of one unit to the input of the next. Keep the total load within the controller and supply rating. Always switch off the supply before wiring. On a long chain, plan the cable path so each 20cm output reaches the next fixture without a splice. The chain wiring also means the controller needs one data line to the first unit, not a cable to every fixture.

Where it fits

The C10 suits bars, restaurants, clubs, and retail displays where color lighting is part of the design. In a bar, a row of 24° units changes color with the music. In a shop, the RGBW white channel lights products cleanly during the day and the color effects take over at night. In a lobby, the same fixture runs slow color washes that do not distract the front desk. In a theater foyer, the SPI sync keeps every unit on the same effect across the room.

Sijil

If certification documents are required for the project, they can be requested from the sales team.

The ILED-CL-A C10 is a straightforward choice for recessed color lighting that has to stay in sync.

• RGB or RGBW COB. The RGBW version adds a white channel, so the same fixture does clean white by day and color effects by night.
• SPI control. Fixtures in a chain respond in sync with the controller, and the system works with a Madrix System.
• Chained cabling. 20cm input and output cables let one unit feed the next without extra boxes in the ceiling.
• Three output levels. 7W at 400 lm, 12W at 600 lm, and 18W (20W) at 1200 lm, with cutouts from 55mm to 95mm.
• Choice of optics. Lenses in 15°, 24°, or 38° cover tight spots and wider washes.
• Solid build. Aluminum housing rated IP42 for dry indoor rooms.
• Documented compatibility. Works with a Madrix System, which matters when the controller is already specified.

For color downlights that have to track a controller, this is the unit we point buyers to first.

The ILED-CL-A C10 suits places where color lighting is part of the design. In bars and restaurants, a row of 24° units changes color with the music or the time of day. In clubs and event spaces, the RGBW white channel keeps the room lit cleanly between color shows.

In retail displays, the fixture highlights products in color during promotions and switches to white for everyday lighting. In theaters and stage foyers, the SPI sync keeps a whole row tracking the same effect. In hotel lobbies, a row of 38° units washes a wall with slow color changes.

The 7W model suits a small accent over a single shelf; the 18W model covers a larger area with 1200 lm. Because the fixtures chain through the input and output cables, a run is wired in sequence rather than star-fed from the controller, which keeps the ceiling wiring short and tidy. For a whole room, a mix of 24° and 38° units covers both accent points and general color wash. In a shop window, the 15° optic keeps the color on the product instead of spilling onto the glass.

A few points to check before you order the ILED-CL-A C10.

• Tegangan. The fixture runs on DC24V or DC12V. Confirm the supply with the order, because the driver input must match.
• Controller. SPI needs a compatible controller, and Madrix System works with this fixture. Check the controller output before ordering.
• Cutout. Cutouts run from 55mm to 95mm depending on the model. Measure the ceiling opening before ordering.
• Lens angle. 15°, 24°, or 38° is fixed at order and cannot be swapped in the field.
• Chain load. The output cable feeds the next unit, so keep the total load within the controller and supply rating.
• Dry indoor only. IP42 is for dry indoor rooms, not outdoor or damp locations. Keep the fixture inside the building envelope.
• Supply and controller. Neither is included with the fixture, so order them with the downlights.

If anything is unclear, send a message to our sales team before ordering. It costs a minute and avoids a wrong fixture.