Светодиодные палубные светильники для бокового освещения, встраиваемые в пол, IP67, 12 В, 24 В, ILED-IG1-4 A

What it does

The ILED-IG1-4 A is a single-side LED deck light you set into the ground or embed in a low wall, so it washes one face at a time. It is not a round uplighter that throws up; it projects to one side, which is what makes it the right fit for a step edge, a path border, or a deck line where you only want light on one direction. It is a low-voltage 12V or 24V unit, so it suits outdoor and damp locations.

Four sizes

The family runs in four bodies. ILED-IG1 A is the smallest at φ42mm, 1W. ILED-IG2 A is φ52mm, 1W. ILED-IG3 A is φ62mm, 1 to 3W. ILED-IG4 A is the largest at φ75mm, 1 to 3W. All four are one-side lighting on a 30° beam. The smaller two suit a single step or a tight border; the larger two cover a wider line. Each has its own cut-hole, so match the size to the opening you cut.

One side, 30° beam

Every unit lights one side only, which is the whole point of the A version. A 30° beam gives a defined, directional wash rather than a soft spread. That reads as a clean line of light along a step or a wall face. If you want the light on both sides of a central border, that is the B version, the double-side model, not this one. Here you point the single face where you want the light to land.

Colour and temperature

Choose a single white from the 2800K to 6500K range, or pick red, green, or blue. The white covers a warm to cool range, so you match the tone to the space. The coloured versions are for a feature edge or a walkway you want to mark out. The LED source is a high-power chip, and the output is 85 to 90 lumens per watt, so a 3W unit gives a strong line for its size.

Power: 12V or 24V, DC or AC

The input is 12V or 24V, and it is available on DC or AC, so it fits both the low-voltage DC runs and the AC outdoor circuits. Keep the supply dry and out of the wet area. Size the supply to the number of lights on the line. Because it is low voltage, it is the safe choice for a place you walk or stand near.

Build and materials

The body is 304 stainless steel and the face is tempered glass. That is the combination that lets it sit in the ground, take foot traffic, and still clear years of weather without corroding. The stainless holds its finish, and the tempered glass spreads the light and shields the source. It is a small, sealed unit, so little can wear out.

IP67 or IP68

The unit is rated IP67, with an IP68 option. IP67 is sealed against dust and against temporary immersion, which covers spray, rain, and a brief flood. IP68 is the deeper-immersion rating for the locations that sit underwater for longer. Pick the rating to the site. The cuthole and the body stay tight, so the joint does not open in the weather.

Installation

Each size has a set cut-hole: φ40mm for the φ42 body, φ46mm for the φ52 body, φ56mm for the φ62 body, and φ64mm for the φ75 body. Cut the opening in the step, deck, or wall to that diameter, set the unit in, and point the light face where you want it. Wire the low-voltage supply. The body is shallow, so it seats flush with a finished surface.

Где это применяется

Use the ILED-IG1-4 A on step edges, walkway borders, deck and terrace lines, low retaining walls, and the base of a hedge or a feature stone. Because it lights one side, it is the right pick for a single-direction line rather than a centred border. The 30° beam keeps it crisp. Where a design wants the light on both sides of a walk, that is the B, double-side model. The IP67 or IP68 body is what suits the outdoor, wet spot.

Что необходимо предоставить

A 12V or 24V power supply sized to the load on the line. The cut-tool for the hole your size specifies. The unit, its body, and the face are all in the box. Keep the supply dry and the line will hold up.

Срок службы и надежность

The high-power chip, the 304 stainless steel, and the tempered glass are the parts that keep it going, and the supplier backs it with a 2-year warranty. It is sealed, has no moving parts, and runs on a low-voltage supply, so the failure points are few. Keep the face out of a direct impact and it holds up. It is CE and RoHS certified.

Why choose the ILED-IG1-4 A.

It is the one-side inground deck light, in four sizes from φ42mm to φ75mm, so it covers a single step to a wide deck line. The 30° beam and the 85 to 90 LM/W output give a crisp, directional wash instead of a soft spread, which is what you want on a step edge or a wall face. The body is 304 stainless steel with tempered glass, rated IP67 with an IP68 option, on a safe 12V or 24V input, DC or AC. Colour is a white from 2800K to 6500K, or red, green, or blue. Each size has its own cut-hole, so the install lines up. It is CE and RoHS certified with a 2-year warranty. If the job is a clean line of light on one side of a step, a border, or a low wall, this is the fixture. It sits flush in the surface and stays there through the weather.

What is the difference between the A and the B model?

The A is one-side lighting: it throws light to one direction, so you point it at the step, wall, or border you want to wash. The B is the double-side version, which throws to both sides of a central line at once. Use the A where you only need one direction, and the B where a walk has light on both sides. The four sizes, from φ42mm to φ75mm, are the same on both.

How do I choose which size?

Match the body to the opening you will cut and the line you are lighting. ILED-IG1 A at φ42mm and ILED-IG2 A at φ52mm are 1W, for a single step or a tight border. ILED-IG3 A at φ62mm and ILED-IG4 A at φ75mm run 1 to 3W, so they give a brighter line for a wider walkway. The cut-holes are φ40mm, φ46mm, φ56mm, and φ64mm, so measure the opening first.

What is the difference between IP67 and IP68?

IP67 is sealed against dust and against temporary immersion, which covers spray, rain, and a brief flood. IP68 is the deeper-immersion rating for a spot that sits underwater for longer. For most step, deck, and border work, IP67 is enough. Pick IP68 for the pool-adjacent and permanently wet locations. Both are the same body and the same 30° beam.

Does it run on DC or AC?

Both. The input is 12V or 24V on DC or on AC, so it fits a low-voltage DC run or an AC outdoor circuit. Pick the one that matches the supply you are already running to the site. The fixture is low voltage, so it is safe to install where people walk or stand. The supply should stay dry, though, since the fixture is the waterproof part.

What colours can I get?

A single white from the 2800K to 6500K range, or red, green, or blue. The white covers a warm to cool range, so you match the tone to the space. The colours are for marking out a walkway or a feature edge. The 30° beam keeps whichever you pick as a clean, directional line.

Put the ILED-IG1-4 A on the lines you light from one direction: step edges, walkway and path borders, deck and terrace lines, the base of a low retaining wall, and the edge of a bed or hedge. Because it throws to a single side on a 30° beam, it is the right pick for a walk you light from one face, not a centred border that needs both sides. The four sizes, from φ42mm to φ75mm, let a row of small units cover a tight step and a row of larger units cover a wide line. The 85 to 90 LM/W output keeps the line crisp. A 12V or 24V input, DC or AC, keeps it safe in the damp location. Choose IP67 for most outdoor work and IP68 for the permanently wet spots. For a low garden border, run the small φ42 and φ52 units in a row so the line stays even, and step up to the φ75 unit where the terrace edge is wider. The single 30° throw is what keeps each line clean and directional. If you need the light on both sides of a walk, that is the B, double-side model.

Check these before you buy the ILED-IG1-4 A. The four sizes run from ILED-IG1 A at φ42mm, 1W, up to ILED-IG4 A at φ75mm, 1 to 3W, and each has a set cut-hole from φ40mm to φ64mm, so measure the opening first. It is one-side lighting on a 30° beam, 85 to 90 LM/W, in 2800K to 6500K white or red, green, and blue. The body is 304 stainless steel with tempered glass, rated IP67 with an IP68 option, on a 12V or 24V input, DC or AC. It ships in a carton of 100 pieces at 0.16kg each, a 36 x 36 x 48cm carton weighing 15.6kg gross. A power supply is not included. The small sealed body and the low-voltage input are what suit the wet, outdoor spot. If the job is a clean line of light on one side of a step or a border, this is the fixture.