Fresnel Spotlight LED Mini 300W 350W for Stage Lighting

The FEL-S2 A is the single-colour member of the FEL-S2 Fresnel family. It pairs a 350W COB LED with a real Fresnel lens, so you get the soft-edged beam that lighting designers reach for in theatre and studio work, without the lamp changes, the heat and the power draw of a tungsten unit of similar output. Where the S2 B adds bi-colour and the S2 C adds full colour mixing, the S2 A keeps things simple: one fixed colour temperature, chosen when you order.

The tungsten look, without the lamp

The standard version runs a 3000K COB chosen to match the warm, familiar colour of tungsten lighting, which is the look most theatres still expect from a Fresnel. Colour rendering is the headline: CRI above 97 and CQS of at least 96, so skin tones and costumes read naturally to both the audience and the camera. If your rig is daylight-balanced, 4000K and 6000K versions are available to order with the same rendering figures.

Optics and zoom

The Fresnel lens gives the fixture its character: a soft-edged pool of light that blends into the surrounding wash instead of cutting a hard circle through it. The beam zooms manually from a 15-degree spot to a 55-degree flood, enough range to move the same fixture between a tight special and a general area wash during a rig check. A motorised auto-zoom version is available as an option if you want the focus under console control.

Control and dimming

Control is DMX512 with RDM, so addresses and status readback can be set remotely instead of on a ladder. The fixture runs one channel for straight dimming, or two channels for 16-bit fine dimming. Four dimming curves are selectable, and the PWM frequency runs from 1 to 20 kHz, so the output stays steady for camera work at the settings film and broadcast crews use. When no console is in the room, built-in programs run the fixture standalone. Connections are 3-pin or 5-pin XLR for DMX plus an RJ45 interface, and power enters through Seetronic connectors with genuine Neutrik available as an option.

Build and cooling

The housing is aluminium with a matte grey finish, and a fan keeps the 350W COB cool through long show days. It measures 481×324×444mm and hangs on a standard lighting stand or rigging point. The rating is IP20, so this is an indoor fixture: stage, studio, and covered venue use.

Power and data connections

Power runs in and out through the Seetronic connectors, so fixtures can be daisy-chained along the truss; specify Neutrik connectors at order if your stock prefers them. Data is on standard XLR, 3-pin or 5-pin, with the RJ45 interface alongside for installations that prefer it. Nothing here needs an external ballast or separate dimmer pack; the fixture is its own dimmer.

Var den används

Theatres and opera houses use it for key light and specials where the warm Fresnel look is still the reference. Television studios put it to work as key and fill light that matches alongside other fixtures on the same camera. Concert and touring rigs take it for the output-to-power ratio, since a 350W draw is gentle on generator supplies. Film and drama sets use the soft beam for scenes shot at high frame rates, where the steady dimming matters. Houses of worship and conference halls value the simple DMX integration, and rental houses stock it as the long-life replacement for their ageing tungsten Fresnels.

Lifespan

The LED source is rated for 50,000 hours. Run twelve hours a day and that is more than eleven years before the source is a question, and there are no lamps to stock or swap in the meantime. The fan and the housing are the only service points, and both are accessible without special tools.

Varför väljer köparna just dessa framför alternativen? Här är vad vi hör från kunderna:

The tungsten look in LED. The 3000K COB with CRI above 97 and CQS of at least 96 gives the warm, soft-edged Fresnel beam that theatre expects, without lamps to change or the heat a tungsten unit puts on the people under it.

One fixture, two jobs. The manual zoom runs from a 15-degree spot to a 55-degree flood, so the same fixture covers tight specials and general wash, and a motorised zoom version is there when the console needs the focus.

Camera-safe dimming. 8- or 16-bit dimming over DMX512 with RDM, four dimming curves and a PWM frequency up to 20 kHz keep the output steady at the frame rates film and broadcast crews shoot.

Simple to rig and run. Standard XLR and Seetronic connections with RJ45 alongside, built-in programs for console-free use, and an aluminium body that hangs on any standard lighting stand.

50,000 hours per source. At twelve hours a day that is over eleven years, which is why rental houses are replacing their tungsten stock with these.

The FEL-S2 A is a 350W single-colour LED Fresnel for indoor stage and studio work, wherever the warm Fresnel look is still the reference.

Theatre and opera. Key light and specials with the soft-edged tungsten-style beam, and no lamp heat on the performers underneath it.

Television and broadcast studios. Key, fill and back light with CRI above 97, so it sits comfortably alongside other fixtures on the same camera.

Concert and touring productions. A 350W draw is gentle on generator supplies and house power, while the output still cuts through a stage wash.

Film and drama sets. The Fresnel beam and steady 16-bit dimming suit scenes shot at high frame rates, where banding would ruin the take.

Houses of worship and conference halls. Warm, flattering light on speakers, and simple integration into an existing DMX system with RDM for remote management.

Exhibition stands and event halls. The built-in programs cover rooms where no console is rigged, and the warm Fresnel pool sits well on presentation stages and product displays.

Rental houses and schools. A 50,000-hour source with no lamps to stock makes it the low-maintenance replacement for ageing tungsten Fresnels in the inventory.

LED Profile Spotlight Alternatives: Top Recommendations for Stage and Studio Lighting (2025)

LED profile spotlights (also known as ellipsoidal reflector spotlights or Lekos) are essential for precise beam shaping, gobo projection, and hard-edged lighting in theaters, studios, and events. They excel at creating focused pools of light with sharp cutoffs using framing shutters, iris, and accessories. If you’re seeking alternatives—due to budget, portability, color needs, or dynamic effects—here are the best options based on current industry trends. These draw from leading brands like ETC, Chauvet, Elation, and Martin, emphasizing LED efficiency, high CRI (90+ for accurate colors), and DMX control. I’ve prioritized versatility for stage/theater use.
1. LED Moving Head Spots (e.g., Chauvet DJ Intimidator Spot 260X or Elation Fuze Spot 120)

Why it’s a great alternative: Replaces fixed profiles with motorized pan/tilt for automated tracking of performers. Offers zoom (10°–50°), gobos, and color wheels for dynamic effects, mimicking profile precision but with movement. 75–120W LEDs provide punchy output equivalent to 575W halogens.
Pros: Instant color changes, sound-activated modes, compact for touring. CRI 90+ for skin tones.
Cons: Higher cost (~$800–$1,500); requires DMX for full control.
Best for: Concerts, dance, and live events where static profiles fall short.

2. LED Ellipsoidal/ERS Lights (e.g., ETC Source Four LED Series or SHEHDS LEKO LED Profile 250W)

Why it’s a great alternative: Direct LED upgrade to traditional profiles—same hard-edged beam, framing shutters, and gobo slots, but with tunable white (3000K–6000K) and 250–350W output. No heat buildup, 50,000+ hour lifespan.
Pros: Seamless drop-in replacement; high CRI 95+; energy-efficient (80% less power than halogen). Manual zoom and accessories compatible.
Cons: Fixed position (no movement); premium pricing (~$1,000–$2,000).
Best for: Theaters and broadcast studios needing precise, static shaping.

3. LED PAR Cans with Beam Control (e.g., Chauvet DJ SlimPAR Pro or Martin VL800 EventPAR)

Why it’s a great alternative: Versatile wash/spot hybrid with adjustable beam angles (15°–60°) and barn doors for edge control. RGBW mixing adds color flexibility absent in basic profiles. 100–200W LEDs flood or focus like a soft-edged profile.
Pros: Affordable (~$200–$600); wireless DMX options; lightweight for quick setups. High CRI 95 for even illumination.
Cons: Softer edges than true profiles; limited gobo projection.
Best for: Small venues, churches, and hybrid wash/spot needs.

4. LED Fresnel Spotlights (e.g., VANRAY 200W LED Fresnel or Nanlite Forza 60C)

Why it’s a great alternative: Provides soft-edged, adjustable beams (10°–50°) like profiles but with warmer diffusion for blending. Bi-color (2700K–6500K) and dimming curves match theater moods. 60–350W output rivals mid-range profiles.
Pros: Silent fans, flicker-free for video; easy zoom. CRI 97+ for natural rendering.
Cons: Less sharp cutoffs; not ideal for gobos.
Best for: Film sets, dance studios, and transitional lighting.

5. LED Soft LED Panels or Cyc Lights (e.g., PROLIGHTS EclPanel TWC or Elation KL Panel XL)

Why it’s a great alternative: For broader coverage, these tunable panels (RGBWW) simulate profile washes with even, soft light and color mixing. 100–300W with diffusion for edge control.
Pros: High uniformity, app/DMX control; CRI 96+ for video. Portable and stackable.
Cons: No tight beams or gobos; bulkier for spots.
Best for: Backdrops, virtual production, and ambient studio fills.