COB Underground LED Light 3-7W Buried Inground Lamp ILED-IG10

What it does

The ILED-IG10 is a COB LED underground uplight you set into the ground so it throws light up and out, washing a step, a tree, a border, or a small feature from below. It is a central uplighter, not a side-lighting deck fitting. It comes in three wattages, 3W to 7W. The COB source keeps the wash smooth and even.

Three sizes

The family runs in three bodies. ILED-IG10 3W is the smallest at φ65mm. 5W is φ80mm. 7W is the largest at φ100mm. All three throw the same 30° beam, or others, at 85 to 90 lumens per watt, so the bigger body gives a brighter, wider pool. The 3W suits a single step or a tree; the 7W covers a wider feature. Each has its own cut-hole, so match it to the opening you cut.

COB LED source

The light comes from a COB chip, not a row of discrete LEDs. That is the whole reason to choose it: a COB source throws one continuous pool of light with no visible dots, so the wash reads as smooth and even rather than dotted. It suits a close-view wash where a standard strip or dot board would show the individual LEDs.

Strålvinkel

The standard beam is 30°, with other angles available to the design. A 30° beam gives a defined, directional wash. The angle sets how far up the surface it reaches before it softens. A narrower beam throws it further up a tree trunk; a wider one opens it into a broad wash of the ground.

Colour and temperature

Choose a single white from the 2800K to 6500K range, or red, green, or blue. The white covers a warm to cool range, so you match the tone to the space. The coloured versions suit a small wash that changes over time. The COB source keeps the colour even across the pool, with no hot dots.

Power: the wide input range

The input is wide. It runs on DC 12V or 24V, on AC 12V or 24V, or on mains 110 to 277VAC and 220 to 240VAC. It fits a low-voltage DC run, a low-AC circuit, or a direct mains install. Pick the version that matches your supply. The low-voltage options are the safe choice where people walk near the light.

Konstruktion och material

The frame is 304 stainless steel and the face is tempered glass. That is the combination that lets it sit in the ground, take foot traffic, and clear years of weather without corroding. The stainless holds its finish; the tempered glass spreads the light and shields the source. It is a small, sealed unit, so little can wear out.

IP65 rating

The unit is rated IP65, which is sealed against dust and against water jets, so it covers spray, rain, and a wet ground. It is the right rating for an inground wash that sits at grade and takes cleaning. Where a location sits underwater for longer, a deeper rating is needed; for most step and border work, IP65 is enough. The cuthole and body stay tight, so the joint does not open.

Installation

Each size has a round body, so the cut-hole matches the diameter: φ60mm for the φ65 body, φ75mm for the φ80 body, and φ95mm for the φ100 body. Cut the opening in the ground, step, or border to that diameter, set the unit in, and point the light up where you want it. Wire the supply you ordered. The body seats flush with the surface.

Var den används

Use the ILED-IG10 on small steps and stairs, tree trunks, border edges, and compact features where you want a smooth uplight wash. The COB source suits a close-view spot where dots would show on a standard board. The three sizes cover a single step with the 3W and a wider feature with the 7W. The 30° beam keeps the wash crisp, and the IP65 body suits the outdoor, wet spot.

Vad du behöver ta med dig

A power supply that matches the input version you ordered: a 12V or 24V supply on the low-voltage versions, or the mains circuit on the AC models. The cut-tool for the hole your size specifies. The unit, its body, and the face are all in the box. Keep the supply dry and the wash will hold up.

Livslängd och tillförlitlighet

The COB chip, the 304 stainless steel, and the tempered glass are the parts that keep it going, and the supplier backs it with a 2-year warranty. It is sealed, has no moving parts, and runs on a low-voltage or mains supply, so the failure points are few. Keep the face out of a direct impact. It is CE and RoHS certified.

Why choose the ILED-IG10.

It is the COB underground uplight in three sizes, from a compact 3W at φ65mm to a 7W at φ100mm. The COB source is the point: it throws one smooth pool of light with no visible dots, which is what you want on a close-view step, border, or tree where a standard LED board would show dots. The 30° beam and the 85 to 90 LM/W output keep the wash crisp and efficient. The body is 304 stainless steel with tempered glass, rated IP65. The input is wide, DC 12V or 24V, AC 12V or 24V, or mains 110 to 277VAC and 220 to 240VAC, so it fits the supply you have. Colour is a white from 2800K to 6500K, or red, green, or blue. It is CE and RoHS certified with a 2-year warranty. If the job is a smooth, dotless uplight wash from the ground, this is the fixture.

What does COB do that a normal LED board does not?

A COB chip throws one continuous pool of light, so you do not see individual LED dots across the wash. A standard board or strip shows the dots, especially at close range. The ILED-IG10 suits a close-view spot like a step edge, a small border, or a tree trunk where the dots would otherwise show. The 85 to 90 lumens per watt keeps it efficient even though the source is a single COB.

How many sizes are there and how do I pick one?

Three: ILED-IG10 3W at φ65mm, 5W at φ80mm, and 7W at φ100mm. All three throw the same 30° beam, or others, at 85 to 90 lumens per watt, so the size sets the brightness and the pool, not the colour. Pick the 3W for a single step or a small border, and the 7W for a wider feature. The cut-holes are φ60mm, φ75mm, and φ95mm, so measure the opening first.

What is the difference between this and the ILED-IG9?

The ILED-IG10 is a COB source in three compact sizes, 3W to 7W, for a smooth, dotless wash. The ILED-IG9 is a discrete Power LED uplight in seven sizes, 3W to 24W, so it reaches the larger, wider jobs. Use the IG10 where you want the dotless COB look on a small, close-view feature, and the IG9 where you need more wattage and a bigger pool. Both are IP65 round uplights on a wide input range.

Is IP65 enough for an inground light?

For most step, border, and small-feature work, yes. IP65 is sealed against dust and against water jets, so it covers spray, rain, and a wet, grade-level location. Where a fixture sits underwater for a long time, a deeper IP67 or IP68 is the better pick. For a wash that comes up out of the ground and takes normal cleaning, IP65 holds up.

What does the wide input range mean?

It means the fixture is offered on DC 12V or 24V, on AC 12V or 24V, and on mains 110 to 277VAC and 220 to 240VAC. Pick the version that matches the supply you are already running to the site, so you may not need a separate transformer. The low-voltage versions are the safe choice where people walk near the light. The mains versions go straight onto the circuit.

Put the ILED-IG10 on the small, close-view surfaces you want to uplight: step edges, stair nosings, border lines, tree trunks, and compact garden features. Because it is a COB source, the wash is smooth with no visible dots, which matters most where someone looks down at the light from close range, a step or a path. The three sizes, from the 3W at φ65mm to the 7W at φ100mm, cover a single step up to a wider feature. The 30° beam keeps the pool crisp, and the 85 to 90 LM/W output stays efficient for the small body. It is IP65 on a wide input range, so it runs on the low-voltage or the mains supply you already have. For a close-view uplight where visible dots would spoil the finish, the COB source is the reason to pick this over a standard LED board. A path, a patio edge, and a raised bed all take the same small, close-view wash. For a bigger, wider wash, move up to the ILED-IG9, and for a directional line along a border, that is the side-lighting IG1-4 family.

Check these before you buy the ILED-IG10. It comes in three sizes, ILED-IG10 3W at φ65mm, 5W at φ80mm, and 7W at φ100mm, so match the body to the opening you will cut. It is a COB source, which is the reason for the smooth, dotless wash, throwing a 30° beam, or others, at 85 to 90 LM/W, in 2800K to 6500K white or red, green, and blue. The build is 304 stainless steel with tempered glass, rated IP65. The input is wide: DC 12V or 24V, AC 12V or 24V, or mains 110 to 277VAC and 220 to 240VAC, so pick the version that fits your supply. It is CE and RoHS certified with a 2-year warranty. A power supply is not included. The COB source is the deciding point where a smooth, dotless uplight wash matters more than raw wattage. If the job is that close-view wash from the ground, this is the fixture.