The ILED-BH-017 is a small window-sill and feature wall light. It is built to sit near a window or on a wall and throw a narrow 10 degree beam, so the light lands where you want it instead of spreading across the whole room. That makes it an accent and highlight fixture: the pick for washing a window sill, lighting a piece of artwork, or bringing up a corner of textured wall. It is compact, built for indoors, and available in two body colours.
ข้อมูลทางเทคนิคโดยสรุป
The fixture is 120 by 110 by 48mm and draws 7W. It throws a narrow 10 degree beam, covers 2800K to 6500K, and puts out light with a CRI above 80. It is sealed to IP42 for indoor use, the body is aluminum with a tempered glass front, and it runs on a 120VAC or 220 to 240VAC supply. It is a Class I fixture, certified to SAA, CE and RoHS.
The narrow 10 degree beam
The 10 degree beam is the point of this fixture. Most accent lights spread their light widely, so a little of it reaches the feature and most of it washes out on the ceiling or floor. This one concentrates the light into a tight, focused wedge, so the window sill or the artwork you point it at gets a strong, clean patch of light and the rest of the room stays calm. Set the angle so the beam lands on the feature and the effect reads as a highlight, not a glare.
Size and where it sits
At 120 by 110 by 48mm it is one of the smaller accent fixtures, so it tucks in on a window sill, a low wall, or a shelf without dominating the space. The 48mm depth keeps it close to the wall, which is what you want for a clean, built-in look. Choose the spot first and let the narrow beam decide where the light lands on the feature below or beside it.
Colour temperature
The light covers 2800K to 6500K, so you pick the temperature to suit the room. A warm 2800K to 3000K white suits a cosy living space and softens a window sill at night. A neutral 4000K is the everyday, all-round choice. A cool 6000K reads brighter and cleaner, which is good for a bright feature or a room that needs to feel sharp.
Indoor rating
The IP42 seal keeps the fixture protected from drips and dust in the air, which is what you want on an indoor wall near a window. It is not a fixture for outdoors, and it should not be used where it will get wet or sit in the weather. It is the right spec for interior feature lighting.
Build and materials
The body is aluminum, which is light and sheds the heat the light puts out. The front is a tempered glass panel that spreads the light and holds the optics. The narrow beam comes from the optics inside the front, and the aluminum body keeps the whole fixture compact. It is a Class I fixture, so it needs to be earthed on install.
ในกล่องมีอะไรบ้าง
Each unit ships as a single fixture with the aluminum body and the tempered glass front. You choose the body colour, white or black, and the colour temperature when you order it.
สิ่งที่คุณต้องเตรียมมา
You will need to wire it to a 120VAC or 220 to 240VAC supply, matching the version you ordered. Because it is a Class I fixture, the installation needs an earth. For dimming, check the fixture is marked dimmable and use a compatible LED dimmer.
สถานที่ที่ใช้
As a narrow-beam accent light it shows up at window sills, on feature and textured walls, and beside a piece of art or a doorway. The small body means it works in a home, an office, a hotel corridor, or a display area where you want a clean patch of light rather than a general light.
อายุการใช้งานและความน่าเชื่อถือ
It draws only 7W, so it is a light, efficient accent light that stays cool. The aluminum body handles the heat without a fan, and the IP42 seal keeps dust out, so it is built to stay on the wall for years. The narrow optics hold the beam steady, which is what makes the highlight read cleanly over time.
