Tiltable 30° LED Cabinet Accent Furniture Downlight ILED-PK-201H

The ILED-PK-201H is a small recessed LED downlight made for cabinets, shelves, and display cases. The head tilts 30°, so the beam can be aimed at the item below after the housing is fixed. At 3W it delivers 135 lm, which is enough to light one shelf or one display compartment without spilling much light into the room. The small body lets the fitting disappear into a shelf edge or a case panel.

Models

Two versions cover the range:

• ILED-PK-201H: 3W, 135 lm, runs on 12VDC, body 52mm diameter by 25mm deep, cutout 42mm
• ILED-PK-201H-HV: 3W, 135 lm, runs on 110-240VAC, body 52mm diameter by 25mm deep, cutout 42mm

The two share the same body and output. The difference is the supply: the 201H works off a 12V DC driver, the 201H-HV connects directly to mains. For a whole run of cabinets, the 12V version keeps the wiring low-voltage; for a single fitting, the HV version avoids a separate driver. The two also pack differently: the 201H ships in a 270mm-tall carton and the HV version in a 540mm-tall carton, so freight volume differs between the two.

Optics and color

Beam angles are 30°, 45°, or 60°, selected at order. The 30° optic matches the product name and suits a tight accent on one item; the 45° and 60° optics spread wider for a shelf or drawer front. CCT ranges 2800K-7000K, so the fixture covers warm interior tones and cooler display areas. CRI is above 80, which is a standard level for accent lighting in cabinets and furniture. The 30° tilt works with all three optics, so the beam lands where the item is, not where the hole happens to be.

Construction

The housing is aluminum with a PC component, finished in white painted, black, or silver, chosen at order. The IP21 rating covers dry indoor use; the fixture is not for damp rooms. The electrical classification is Class II. The tilt mechanism is part of the trim, so aiming is done by hand after the housing is seated.

Controls and electrical

The 201H version runs on 12VDC and takes its power from a constant-current LED driver built into the system. The 201H-HV version runs directly on 110-240VAC with power factor above 0.9. Both use a built-in constant-current driver, so neither needs an external power box behind the panel. Wiring must be off at the breaker before installation, and on a 12V run the cable should be sized for the total load of the loop.

Kurulum

The fixture recesses into a cabinet shelf, a display case panel, or a furniture board. Cut a round opening to 42mm, feed the cable, then seat the housing. Aim the head before the trim is locked into place, and adjust again later if the display changes. On a 12V run, keep the cable runs short enough to avoid voltage drop across the loop. On a mains run, the HV version connects through its own driver without an external unit.

Where it fits

The 201H suits cabinets, shelves, display cases, jewelry cases, and museum cases. In a shop display, a row of 30° units picks out each item while keeping the case interior even. In furniture, the small body hides inside a shelf edge and lights the surface below. The 30° tilt lets the beam reach the front of a deep shelf, not just the back, which is where most accent fittings fail.

Garanti ve sertifikalar

The ILED-PK-201H carries CE, RoHS, SAA, and TUV certification, and is covered by a 3 year warranty. If the project needs certification documents on file, they can be requested from the sales team.

The ILED-PK-201H is a small answer for lighting inside cabinets and display cases.

• Tiltable head. The 30° tilt aims the beam at the front of a deep shelf or a single display item.
• Two supply options. The 201H runs on 12VDC; the 201H-HV runs on 110-240VAC, so the same body covers low-voltage runs and direct mains.
• Small body. 52mm in diameter with a 42mm cutout, so it hides inside a shelf edge or case panel.
• Choice of optics. Beam angles of 30°, 45°, or 60° cover tight accents and wider shelf lighting.
• Wide color range. CCT from 2800K to 7000K matches warm wood interiors and cooler display areas.
• Finish options. White painted, black, or silver bodies fit light and dark furniture.
• Documented compliance. CE, RoHS, SAA, and TUV certification, with a 3 year warranty behind the unit.

For cabinet and display accent lighting, this is the fitting we point buyers to first.

The ILED-PK-201H suits places where a small light has to fit inside furniture or a display case. In shop displays, a row of 30° units picks out each item in a case while keeping the interior even. In jewelry cases, the tight beam lights a single piece without washing out the glass.

In museum cases, the small body hides inside the panel and the tilt aims the light at a specimen or artifact. In kitchens, the same housing lights cabinet interiors and drawer fronts. In furniture, the 52mm body sits inside a shelf edge and lights the surface below.

Because the head tilts 30°, the beam can reach the front of a deep shelf, not just the back. The 12V version suits whole runs of cabinets with one low-voltage supply; the HV version fits single locations with a direct mains connection. For warm wood interiors, set the CCT around 2800K; for cooler display areas, move toward the top of the 2800K-7000K range. In a row of display cases, keep the same beam angle across the run so the light looks consistent from the front.

A few points to check before you order the ILED-PK-201H.

• Supply. The 201H runs on 12VDC; the 201H-HV runs on 110-240VAC. Confirm which the project needs and state it with the order.
• Cutout. Both versions use a 42mm cutout with a 52mm body. Check the board thickness before drilling.
• Beam angle. 30°, 45°, or 60° is fixed at order. The lens cannot be swapped in the field.
• Finish. White painted, black, or silver is fixed at order. Confirm the color before delivery.
• Wiring. Switch off the supply before installing. On a 12V run, keep cable runs short enough to avoid voltage drop.
• Packaging. The 201H ships 100 pieces per carton at 340x340x270mm, 6.2kg net; the 201H-HV ships 100 pieces per carton at 340x340x540mm, 11kg net. Use these figures for freight planning.

If anything is unclear, send a message to our sales team before ordering. It costs a minute and avoids a wrong fitting.