LED Wall Pack Light 40W-120W Meanwell Driver

The ILED-WP1 is a die-cast aluminum LED wall pack luminaire designed for surface-mounted installation on exterior and covered interior walls. It is available in three fixed wattage ranges — 40W–60W, 70W–100W and 110W–120W — all using the same 333 × 250 × 159 mm rectangular housing. The WP1 delivers 110 lm/W from LumiLEDs 3030 LEDs inside a gray die-cast aluminum body with an integrated PC lens. IP65+IK10 rating makes it suitable for direct outdoor exposure, and optional DALI 2-way dimming, corridor-mode motion sensor and emergency battery backup extend its application range.

Thông số kỹ thuật tại một cái nhìn

Model: ILED-WP1
Wattage ranges: 40W–60W / 70W–100W / 110W–120W (three fixed models)
Luminous efficacy: 110 lm/W (all models)
Housing dimensions: 333 × 250 × 159 mm (identical across all wattage ranges)
Nguồn LED: LumiLEDs 3030 SMD
Beam angle: 120°
Nhiệt độ màu: 2800K – 6500K (điều chỉnh được bằng công tắc ngả)
Chỉ số hoàn màu (CRI): 82
Điện áp đầu vào: 220–240VAC / 110–277VAC dải kép
Hệ số công suất: 0.9
Chỉ số bảo vệ IP: IP65 — kín bụi, bảo vệ khỏi tia nước
Đánh giá chịu va đập: IK10 — Khả năng chống chịu 5 joules
Materials: Die-cast aluminum body, gray finish, PC lens
Phân loại điện: Loại I
Chứng nhận: SAA, CE, RoHS
Bảo hành: 3–5 năm
Optional features: DALI 2-way dimming, corridor-mode motion sensor, emergency battery

Wattage range comparison

All three WP1 models share identical housing dimensions (333 × 250 × 159 mm) and the same 110 lm/W efficacy. The difference lies only in wattage and lumen output. The 40W–60W model is the entry-level option, suitable for low-ceiling perimeter lighting and narrow walkways. The 70W–100W model sits in the mid-range, covering standard building entrances and small parking bays. The 110W–120W model is the highest-output option, designed for wide parking areas, loading docks and large building facades requiring broad flood illumination.

Because the housing size is identical across all three models, retrofitting between wattage ranges does not require any modification to mounting brackets or wiring conduits. Select the wattage range that matches your illuminance target and mounting height — the 110W–120W model produces the highest output but draws proportionally more power, so running costs scale accordingly.

Build and weather resistance

The WP1 housing is a die-cast aluminum body with a gray powder-coat finish, cast as a single piece for structural integrity. The 159 mm depth accommodates the driver compartment and heat sink within a low-profile rectangular form that mounts flush against exterior walls without protruding significantly. The PC lens covers the full LED array and carries the IK10 impact rating — the highest standard for luminaires — absorbing a 5 joule impact without cracking. This is particularly relevant for wall pack lights installed at accessible heights where accidental impact from vehicles, equipment or maintenance activities is possible.

The IP65 seal protects the internal driver and LED array from dust ingress and water jets from any direction, making the WP1 suitable for unsheltered outdoor installation in rain, snow and wind-driven spray. The die-cast aluminum body also provides inherent corrosion resistance, important for coastal or de-icing-salt environments where exposed steel housings would degrade over time.

Điều khiển và lắp đặt

The WP1 offers three optional upgrades: DALI 2-way dimming, corridor-mode motion sensor, and emergency battery backup. These are selected at order time — they are not retrofittable. DALI 2-way dimming adds individual fixture addressing (0–63) on a 2-wire bus, allowing group control, scene setting and status feedback including lamp hours and fault codes. The WP1 does not accept 0-10V or TRIAC analog dimming — a DALI-to-analog converter is required if your building system uses those protocols.

The corridor-mode motion sensor keeps the fixture at low stand-by output when unoccupied, then ramps to full brightness within 1–2 seconds of detecting movement — effective for building entrances, stairwells and low-traffic corridors where full output is only needed intermittently. The emergency battery provides approximately 90 minutes of reduced-output light during a power failure, satisfying egress lighting requirements in many jurisdictions.

Installation uses a surface-mount backplate with pre-drilled fixings for brick, concrete or timber stud walls. The Class I rating requires a protective earth connection. Universal 110–277VAC input covers both North American and European supply standards. The 120° beam angle provides wide, even wash illumination ideal for wall-mounted perimeter lighting at mounting heights between 2.5 m and 4 m.

Three wattage ranges in one housing.
— The WP1 is available as 40W–60W, 70W–100W or 110W–120W, all sharing the same 333 × 250 × 159 mm die-cast aluminum housing. This means you can mix wattage ranges on the same project without changing mounting hardware or conduit sizes — ideal for phased installations or mixed-application sites.

Kháng va đập IK10.
— The WP1 carries an IK10 rating — the highest standard for luminaires — absorbing a 5 joule impact without cracking. For wall pack lights installed at accessible heights near parking areas and loading docks, IK10 significantly reduces replacement costs from vehicle and equipment strikes.

IP65 outdoor rated.
— The WP1 is sealed against dust and water jets, suitable for direct outdoor exposure without additional weatherproofing. The die-cast aluminum body provides inherent corrosion resistance, important for coastal or de-icing-salt environments.

DALI, sensor and emergency options.
— All three optional features are available on the WP1 platform, but each must be selected at order time — they are not retrofittable. Plan your control and safety requirements before placing the order.

Building entrances and perimeters.
— The WP1’s 120° beam provides even wall wash at building entrances and perimeter walls. IP65 seal withstands rain and wind-driven spray. IK10 protects against vehicle and equipment strikes.

Parking lots and car parks.
— Perimeter-mounted WP1 provides spill light onto parking areas, reducing pole fixture counts. The 110W–120W model covers wide zones; the 40W–60W suits narrow aisles. IK10 is essential where vehicle doors and ladders may strike.

Loading docks and service entrances.
— Die-cast aluminum body withstands loading dock temperature extremes, vibration and impact. IP65 seal protects against wash-down cleaning and rain through open dock doors. Optional emergency battery covers egress during power failures.

Security and access point lighting.
— The WP1’s CRI >82 renders faces, vehicle colours and security tags in natural colour, improving facial recognition and CCTV footage quality. When paired with the optional motion sensor, the WP1 can operate at low stand-by output to deter loitering while conserving energy, then ramp to full brightness within 1–2 seconds of detecting movement at access points.

Housing identical across all wattage ranges. — All three WP1 wattage models share the same 333 × 250 × 159 mm housing. Mixing ranges on one project requires no bracket or conduit changes — select each model for its location’s illuminance needs.

DALI is optional, not standard. — Base WP1 is on/off only. DALI 2-way is an optional upgrade at order time. No 0-10V or TRIAC support — a DALI-to-analog converter is required for those protocols.

Motion sensor is optional. — Corridor-mode motion sensor is an optional upgrade at order time — not built in, not retrofittable. Include it if occupancy sensing is a project priority.

Emergency battery is optional. — Emergency battery is not standard on the WP1 — specify at order time. If egress lighting is required at your entrances, confirm the option before ordering; it cannot be retrofitted.

Gray finish standard. — The WP1 ships with a gray powder-coat finish as standard on the die-cast aluminum body. This neutral colour blends into most commercial and industrial building façades without drawing attention to the fixture itself. Custom colours are available as special orders at additional cost.