Đèn thả công nghiệp Edison chiếu sáng trong nhà cho phòng khách, đế E27 phong cách cổ điển, đèn thả trần loft retro

The ILED-PD5 is the pendant that started the industrial look: a black metal shade on a cord, an E27 socket inside, and the bulb itself on display. There is no diffuser, no hidden engine and no plastic to apologise for — the fitting is the shade, the cord and the socket, and the bulb you screw into it is part of the design rather than a component to hide.

The shade and the cord

The shade is metal, finished black, proportioned to throw a 120° beam down and out without blinding anyone at the dining table. The cord suspension is set to the drop the space needs, so the same fixture hangs low over a café table or higher over a kitchen bench. Black is the finish the loft interiors call for; it reads against brick, timber and white plaster, and it disappears against a dark ceiling.

The E27 bulb is the source

The fixture takes any standard E27 bulb, and that choice is the whole personality of the light. An Edison-style filament LED gives the vintage look the retro interiors want. A plain warm-white LED gives more lumens for a working kitchen. The specification covers LED bulbs at 80 lumens per watt, CRI above 80, colour from 2800K to 6500K — warm tungsten through to cool daylight — so the bulb decides where the light lands on that scale. A dead bulb is a ten-second swap, and an upgrade later is a bulb change, not a fitting change.

Nơi được sử dụng

Over the living room corner or the reading chair, hung low with a warm filament bulb. Over the kitchen bench or the dining table, where a pair of them runs the length of the counter. In cafés, bars and loft conversions, where the black shade and the visible bulb are the look the fit-out is paying for. And over retail displays and stair positions, where the industrial fitting suits the merchandise or the space.

Wiring and installation

The fixture runs on 220-240VAC, is rated IP42 for dry indoor rooms, and carries SAA, CE and RoHS certification with a two-year warranty. The installation is the simple pendant procedure: fix the canopy, wire the cord, hang the shade, screw in the bulb. Confirm the earth at the ceiling point before ordering, and have the wiring done by a licensed electrician. Because the shade is metal and the bulb sits open inside it, the bulb choice also sets the glare: a filament bulb reads soft from the side, while a bare bright LED reads hot from below, which is why the living room positions usually run the warmer, gentler bulbs.

Choosing the bulb

Three decisions set the light: the colour temperature against the room, the brightness against the table or the floor below, and whether the bulb dims. A dimmable bulb pairs with a compatible dimmer for the evening setting; a non-dimmable bulb switches. Match the bulb’s beam and lumens to the position, and keep the spare bulbs with the fitting, because the industrial look depends on the bulb that is in it. One practical note: keep every bulb in a multi-pendant row the same model, because a mixed set of colour temperatures reads as a fault from across the room.

Specifying the pendant

Four decisions shape the order: the drop height against the table or the bench, the bulb against the light the position needs, the number of fittings against the run, and the dimmer against the bulbs if the evening setting matters. Confirm the earth at the ceiling point early, because the wiring is the one part of the job that is not visible at the end but is the part the inspection cares about. With those set, the fitting is the simplest pendant in the range to order: a shade, a cord, a socket and a bulb.

Why do buyers pick the ILED-PD5 over the alternatives? Here is what we hear from customers:

The bulb is the design. The shade and the socket put the Edison-style bulb on show, which is the look the loft and retro interiors are buying. When the bulb changes, the fixture changes with it.

One fitting, any room. The black metal shade reads against brick, timber, plaster and tile, which is why the same pendant turns up over kitchen benches, café tables and stair positions in the same project.

Nothing to maintain but the bulb. There is no diffuser and no hidden engine; a dead bulb is a ten-second screw swap, and the fitting outlives several generations of bulbs.

Honest materials. Metal shade, metal canopy, black finish over metal. It suits the industrial interiors at close range, not just in the product photo.

Certified for the market. SAA, CE and RoHS, IP42 for dry indoor rooms, 220-240VAC, and a two-year warranty on the fitting.

The ILED-PD5 hangs in the interiors that want the bulb on show: the loft conversions, the retro kitchens, the café fit-outs where the industrial look is the brief.

Living rooms and reading corners. Hung low beside the sofa or the armchair with a warm filament bulb, the black shade throwing the pool of light down and the bulb throwing the pattern on the ceiling.

Kitchen benches and dining tables. A pair or a row of pendants along the counter, each at the same drop, with brighter neutral bulbs for the working surface and dimmable ones for the evening.

Cafés, bars and restaurants. The industrial look over the tables and the bar, where the black shade and the visible filament bulb are the ambience the fit-out is paying for, and a dead bulb is a ten-second fix between services.

Loft conversions and studios. The pendant against brick and blackened steel, where the fitting belongs to the architecture rather than decorating it.

Retail displays and stair positions. The shade marks the position and the bulb lights the display, and the industrial fitting suits the merchandise the way a recessed downlight never does.