Modern Outdoor Wall Light with Pir Sensor ILED-BH-020 C

The ILED-BH-020 C is the sensor version of the square wall light range: a 140×140×180mm fitting that washes a wide spread of light across the wall it sits on, and lights up on its own when someone walks up. Where the up-and-down fittings in the range mark a wall with two narrow beams, this one throws a broad 120-degree wash — the kind of light you want on a door approach or a garden path, where the fitting should greet people rather than decorate around them.

The light it throws

The fitting runs 12W behind an acrylic diffuser that spreads a 120-degree wash with no LED dots or hot spots on the wall. Colour rendering is above 80, and the colour temperature spans 2800K to 6500K, specified at order — warm for a front door, cooler for a side passage or service approach. It is a greeting and wayfinding light rather than a floodlight, and it reads best mounted beside a door or along a walking route.

The PIR sensor

The built-in PIR motion sensor watches the approach and switches the fitting on when someone moves into range, then off again after they pass. That behaviour changes what the fitting is for: on a garden path or side door it provides light only when there is someone to use it, which trims the running hours without anyone remembering a switch, and on an entrance it greets people arriving after dark. The sensor is built into the fitting at the factory, so there is no separate detector to mount or aim on site, and no control wiring beyond the normal supply.

Build and finish

The body is aluminium with an acrylic diffuser, closed on a silicone gasket and sealed to IP65 against dust and water jets from any direction, so it mounts on exposed walls in the full weather. The finish is black or white — black against brick and dark render, white where the fitting should sit quietly on a light wall.

Electrical

The fixture runs on 220-240VAC or 120VAC, Class I wired, with the driver inside the body. Colour temperature is locked in at order; there is no switch to change it afterwards, so confirm it when you specify.

Những gì bạn cần cung cấp

You need the wall fixings suited to the surface — masonry plugs for brick and block, suitable screws for timber framing — and a switched, fused circuit with a protective earth for the Class I connection. The Allen key for the body comes in the accessories. An electrician should make the hardwired connection per local code, and since the driver, sensor and LEDs are all integral there is no lamp stock or spare module to hold for the fitting.

Mounting

Installation is a surface mount onto the supplied back plate. An Allen key in the accessories opens the body; mark, drill and plug the wall, fix the plate, terminate live, neutral and earth into the terminal block, and close the body over the gasket. The earth connection is mandatory on this Class I fitting, so an electrician should make the connection.

Nơi được sử dụng

Front doors and side entrances are the main job — light when someone arrives, dark when nobody is there. Garden paths, courtyard steps and driveway walls use the sensor to light the route without running the fitting all evening. On commercial fronts it covers service doors and side approaches that need light on demand rather than light all night. Balconies, terraces and shed or garage walls fill out the rest of the order.

Chứng nhận

The ILED-BH-020 C carries SAA for Australia and New Zealand, CE for Europe, and RoHS. The sealed body needs no routine work inside; a wipe of the diffuser face during site maintenance keeps the light even.

Vì sao người mua chọn những sản phẩm này thay vì các lựa chọn khác? Đây là những gì chúng tôi nghe được từ khách hàng:

Light when someone arrives. The built-in PIR sensor switches the fitting on for the approach and off after, so a side door or path is lit on demand without anyone touching a switch.

A broad, even wash. 12W behind an acrylic diffuser spreads 120 degrees with no LED dots — light across the wall and the steps in front of it, not a narrow beam.

IP65 on an exposed wall. Sealed on a silicone gasket against dust and water jets, so it takes the full weather beside a door or along a path.

Aluminium with an even face. The body takes the knocks, and the diffuser holds a smooth light in black or white to match the wall.

Simple Class I wiring. 220-240VAC or 120VAC with the driver and sensor inside the body — a back plate, a terminal block and nothing else to mount.

The ILED-BH-020 C is a square 12W LED wall light with a built-in PIR sensor, for approaches that should light themselves when someone arrives.

Front and side doors. The fitting greets people arriving after dark and switches off again afterwards, with no switch to find and no light burning all night.

Garden paths and courtyard steps. The sensor lights the route as someone walks it, which keeps the running hours short on the stretches of the garden used late.

Driveway and garage walls. A broad wash beside the garage door or along the drive wall, switching on when the car arrives and off again once it is parked, without burning through the night.

Commercial service doors. Side approaches and delivery doors that need light on demand rather than a fitting burning through the empty hours.

Balconies and terraces. The IP65 body takes the exposed position, and the smooth acrylic face gives even light across a small outdoor room.

Sheds, workshops and store entrances. Hands-free light at the door, which is exactly what you want when carrying something through it in the dark with both hands full.