Đèn chiếu sáng LED hình bầu dục 10W 220mm IP65

The ILED-BH-O220 is a narrow oval bulkhead light built for installations where space is tight and a round fixture would look too wide. At 220×135mm it fits corridors, stairwells and narrow entryways where a standard round bulkhead would overhang the mounting surface. The elongated shape spreads light along the length of the space rather than radiating outward, which is more efficient for linear areas like walkways and hallways.

Thông số kỹ thuật tại một cái nhìn

The ILED-BH-O220 is available in two wattage options. The 8W version produces 880 lumens. The 10W version produces 1100 lumens. Both deliver 100–110 lumens per watt from the same 220×135×65mm housing. Input is 220-240VAC or 110-277VAC 50/60Hz, so the fixture works in most regions without a transformer. The colour temperature range is 2800K to 6500K, selectable at installation — warm white, neutral, or cool white. Colour rendering is above 82. The beam angle is 120°, spreading light evenly across the floor. Four diffuser variants are available: Plain for general illumination, Grille Crossing (GL) for applications where the light pattern needs to be broken up, Eyelid Half Moon (EL) for directional wall-washing or facade grazing, and Crossing (TL) for a balanced spread with partial glare control. The die-cast aluminium body is IP65 rated — dust-tight and protected against water jets from any direction.

Kết cấu và lắp đặt

The housing is die-cast aluminium with a powder-coated finish in white, black or silver gray. The diffuser is anti-UV polycarbonate, available in four patterns as described above. The integral driver is sealed inside the housing — no external ballast or separate power supply is needed. Wiring is direct to mains through the terminal block. Electrical classification is Class I, requiring a protective earth connection. The fixture can be surface-mounted to a flat wall or ceiling using the four mounting points on the back plate, or recessed into a 220×135mm cutout if the construction allows.

Control options

This is a standard non-dimmable, non-controlled bulkhead. It switches on and off with the circuit — wall switch, timer, or external sensor. For projects that require DALI dimming, motion sensing, or photocell control, order the emergency or wall-packed variants from the same series instead.

Những gì có trong hộp

Each unit ships as a single bulkhead with the driver pre-installed, mounting hardware included and the terminal block ready for connection. The selected diffuser (Plain, GL, EL or TL) is factory-fitted and should not be removed after installation. No separate controllers, transformers or drivers are packed inside — the fixture is ready to wire direct to mains.

Những gì bạn cần cung cấp

A circuit breaker or wall switch for on/off control. A mounting surface suitable for the fixture weight. For outdoor installations, confirm the mounting location is within the IP65 protection zone and that the seal remains intact after installation. No special tools beyond a screwdriver and wire strippers are required.

Nơi được sử dụng

The ILED-BH-O220 is built for narrow linear spaces where a round bulkhead would look disproportionate. Hotel and office corridors use the elongated form to follow the length of the passage with fewer fixtures than a round layout would require. Stairwells and narrow entryways benefit from the compact 220×135mm footprint — the fixture fits where a 300mm round bulkhead would overhang. External walkways and car park boundaries take advantage of the IP65 weatherproofing and the choice of diffuser patterns to control light spread and glare. The 3CCT option lets a single SKU serve warm-white hospitality zones and cool-white security areas across the same project.

Chứng nhận và bảo hành

The ILED-BH-O220 carries SAA, CE and RoHS certifications. SAA approval covers Australian and New Zealand market requirements. The warranty period is three to five years depending on the region and distributor terms.

Vì sao người mua chọn những sản phẩm này thay vì các lựa chọn khác? Đây là những gì chúng tôi nghe được từ khách hàng:

Narrow oval shape fits tight spaces. At 220×135mm the O220 is noticeably narrower than a round 300mm bulkhead. In corridors and stairwells where wall space is limited, the oval form follows the passage length without overhanging — fewer fixtures cover the same distance than round layouts.

Four diffuser options from one family. The O220 is available in Plain, Grille Crossing (GL), Eyelid Half Moon (EL) and Crossing (TL) diffusers. All four share the same housing and mounting pattern, so specifiers can mix patterns across a project without changing fixture dimensions or wiring.

8W or 10W, same housing. The two wattages share the identical 220×135×65mm enclosure. Specifiers can order the lower output for narrow passages and step up to 10W for wider areas without adjusting mounting hardware or ceiling cutouts.

Wide input voltage range. The fixture accepts both 220-240VAC and 110-277VAC, so it works in most regions without a transformer. This simplifies procurement for international projects compared to fixtures limited to a single voltage.

The Oval LED Bulkhead Light (ILED-BH-O220) is designed for wall and ceiling mounting in narrow linear spaces where a round fixture would look disproportionate.

Hotel and office corridors. The narrow 220×135mm oval form follows the passage length, covering more distance per fixture than a round equivalent. The IP65 seal handles normal indoor dust, and the 3CCT option lets specifiers match warm-white hospitality zones with cool-white task areas from the same SKU.

Stairwells and narrow entryways. The compact footprint fits tight wall spaces where a 300mm round bulkhead would overhang. The elongated shape spreads light along the stair run rather than radiating outward, giving more even illumination across the steps.

External walkways and car park boundaries. IP65 weatherproofing handles rain and washdown. The four diffuser options let specifiers choose the light pattern that best suits the application — Plain for general coverage, GL for softer diffusion, EL for wall-washing, or TL for balanced spread with partial glare control.

Loading bays and service corridors. These areas combine moisture, dust and physical impact with a need for reliable general illumination. The sealed die-cast aluminium housing and gasketed PC diffuser protect internal components. The 8W/10W range covers both narrow service passages and wider bay areas from the same housing.

Một vài điều cần kiểm tra trước khi đặt hàng:

Diffuser selection. Four variants share the same housing: Plain for general illumination, Grille Crossing (GL) for softer diffusion, Eyelid Half Moon (EL) for directional wall-washing, and Crossing (TL) for balanced spread with partial glare control. Confirm the pattern before ordering — the diffuser is factory-fitted and cannot be swapped after installation.

Wattage selection. The 8W version delivers 880 lumens; the 10W version delivers 1100 lumens. Choose based on the illumination level — 8W for narrow corridors, 10W for wider walkways.

Colour temperature. Three fixed settings are available at installation: 2800K warm white, 4000K neutral and 6500K cool white. Set the switch before closing the diffuser — it cannot be changed after installation.

Mounting type. The fixture can be surface-mounted to any flat wall or ceiling, or recessed into a 220×135mm cutout. Confirm the mounting surface supports the fixture weight.

SAA compliance. If the project requires SAA approval for Australian or New Zealand markets, confirm this variant carries the certification. The ILED-BH-O220 lists SAA on its specifications table.