Dải đèn LED SMD 5050 RGB linh hoạt 12V 24V DC ’

What is the ILED-FX-5050 RGB LED Strip?

The ILED-FX-5050 RGB is a static colour RGB LED strip built around the proven 5050 SMD package — a 5.0 mm × 5.0 mm housing containing separate red, green, and blue LED chips. It produces dynamic colour effects by mixing these three channels at adjustable intensities. Unlike addressable strips such as WS2812B, the entire strip changes colour as a single unit. One controller manages the whole run, which keeps wiring simple and cost down.

Four Density Options

The FX-5050 RGB comes in four LED-density variants. The 30 LEDs/m model draws 7.2 W/m and is the most economical choice for long runs where absolute brightness is not critical. The 48 LEDs/m model sits at 11.5 W/m and offers a middle ground. The 60 LEDs/m model delivers 14.4 W/m for applications that need stronger colour output. The 120 LEDs/m model pushes 28.8 W/m and provides the brightest output, but it is 24VDC only and uses a wider 13.5 mm PCB.

All models share the same 120° beam angle and cut every 25 mm. Lower-density models use a 10 mm PCB; the 120 LEDs/m model uses 13.5 mm. Standard 5m rolls; custom lengths available.

Kết cấu và lắp đặt

The strip is mounted on a flexible printed circuit with 3M adhesive backing. The standard backing is yellow 3M tape; red 3M tape is available as an option for applications where the colour of the adhesive matters. Copper traces run along the length of the PCB, and each cut point exposes solder pads for joining sections or attaching connector cables.

Installation is straightforward. Peel back the adhesive backing, position the strip, and press into place. Connect the 15 cm input cable to a compatible RGB controller and power supply. If multiple strips are joined end-to-end, use the appropriate connector or solder the copper pads and insulate with heat-shrink tubing. The 30/48/60 models accept either 12VDC or 24VDC input; the 120 LEDs/m model requires 24VDC.

IP rating options

Four IP ratings cover the range from dry indoor use to continuous underwater immersion. IP20 has no coating and is suited to protected indoor coves and shelving. IP65 adds a silicone cover that protects against water jets — suitable for covered outdoor areas such as fascia lighting and awning edges. IP67 allows temporary submersion and is used for pool and fountain installations. IP68 is rated for continuous submersion and is the choice for permanent underwater fixtures. Do not mix IP variants on the same run — the connector types differ and cannot be sealed together.

Controller compatibility

The ILED-FX-5050 RGB works with any standard 3-channel PWM RGB controller. The controller must match your strip voltage — 12VDC controllers work with the 30/48/60 models; 24VDC controllers are required for the 120 LEDs/m model. Most budget RGB controllers offer colour wheels, dimming, and basic scene presets. No DMX, ArtNet, or SPI protocol is needed — this is a simple plug-and-play RGB strip.

Những gì có trong hộp

Each order ships as a 5-metre roll (or custom length if specified) with the 15 cm input cable pre-attached. The roll is wound onto a plastic spool for shipping. No controller or power supply is included.

Những gì bạn cần cung cấp

To complete the installation you will need: a 3-channel PWM RGB controller compatible with your chosen voltage (12VDC or 24VDC), a power supply rated for the total wattage of the strip plus 20% headroom, and connector cables or soldering materials if you are joining multiple sections. For outdoor installations, also plan for waterproof connector seals at every joint.

Nơi được sử dụng

Residential ambient and accent lighting is the most common application. The FX-5050 RGB is installed in ceiling coves, under-shelf cavities, and behind TV units to create mood lighting that shifts with the time of day or the occasion. Retail displays use the strip for colour-wash effects that draw attention to products and seasonal promotions. Bars, clubs, and hospitality venues rely on the full RGB spectrum to set atmosphere quickly across a single zone. Architectural outline lighting uses the bendable PCB to trace building edges, windows, and rooflines — IP65 and above variants for exterior use. Holiday and event decoration takes advantage of the easy cut-and-join design to create temporary installations.

Thời gian sử dụng và độ tin cậy

The ILED-FX-5050 RGB is rated for 50,000 hours of operation. At 12 hours per day of use, that works out to roughly 11.4 years before light output drops to 70% of initial brightness (L70 standard). The 5050 SMD package is a mature technology with established thermal management — the copper PCB acts as a heat spreader, and no active cooling is required. The limiting factor for lifespan is usually the adhesive losing grip or the silicone degrading under UV, not the LEDs themselves. Choose IP65 or above for outdoor use.

Why do buyers pick the FX-5050 RGB over other strips? Here is what we hear from customers:

Simple control. A standard 3-channel PWM RGB controller drives the entire strip — no DMX, no protocol conversion, no addressable ICs to program. Plug it in, set the colour, and you are done. This simplicity also means lower cost at the controller end.

Four density options. Whether you need economical long runs at 30 LEDs/m or maximum brightness at 120 LEDs/m, there is a variant that fits. The 30/48/60 models all run on 12VDC or 24VDC, so you can mix voltages across different zones without changing hardware.

IP coverage for any environment. From dry indoor coves (IP20) to submersible pool lighting (IP68), the same strip form factor covers the full range. Just order the right variant for your installation — the silicone coating differs between ratings and cannot be changed after manufacture.

Easy to install and modify. The 3M adhesive backing sticks to clean, dry surfaces without tools. Cutting every 25 mm lets you fit odd-length spaces precisely. Solder or connector joints between sections are straightforward.

Residential ambient and accent lighting. — Ceiling coves, under-cabinet kitchen strips, and TV backlighting all benefit from the FX-5050 RGB’s wide 120° beam and static colour control. IP20 is sufficient for these dry indoor locations. The strip conforms to curved coves and tight corners without losing adhesion.

Retail display colour-wash. — Dynamic colour changes draw the eye to featured merchandise and support seasonal or promotional themes. The 120° beam angle distributes colour evenly across display surfaces. IP65 variants extend the same approach to covered entrance canopies and outdoor signage backlights.

Bar, club, and hospitality atmosphere lighting. — Venues that change mood between service periods — warm white for breakfast, deep colour for evening — get reliable single-zone control from a single PWM controller. IP65 and IP67 variants suit outdoor terraces and poolside installations.

Architectural outline and holiday decoration. — The flexible PCB traces building edges, window frames, and rooflines. IP65/IP67/IP68 ratings cover outdoor exposure. Custom lengths are available when standard 5 m rolls do not match the project dimensions.

Marine and automotive accent trim. — The IP68 variant handles vibration and moisture exposure in boats, campers, and custom vehicle builds. The 3M backing adheres to cleaned metal, fiberglass, and painted surfaces.

Event and stage backdrop lighting. — Temporary installations benefit from the tool-free adhesive mount and straightforward controller wiring. Colour sweeps across walls or ceilings are set in seconds and reversed just as easily after the event.

Static RGB — not addressable. — The FX-5050 RGB changes colour as a single unit across the full strip. It cannot display different colours on different sections. For multi-zone or animated effects, select an addressable RGB strip instead.

CRI does not apply. — CRI is a rating for white light sources only. The FX-5050 RGB produces RGB hues — red, green, and blue — not a fixed white colour. If you need CRI >90 white light, select a white COB or SMD strip.

24VDC recommended for longer runs. — The 30/48/60 LEDs/m models support both voltages, but for runs over 3 metres, 24VDC is strongly recommended to minimise voltage drop and maintain colour consistency. The 120 LEDs/m model requires 24VDC exclusively.

Do not mix IP ratings on one run. — Each IP variant uses a different silicone coating and connector type. Mixing them creates moisture entry points. Order the correct IP variant for your entire installation.

Size your power supply with headroom. — Always add at least 20% current margin above total strip wattage. A 5 metre run of 60 LEDs/m draws 72 W — use a power supply rated for at least 90 W.