The ILED-FX-3528 240 is a flexible LED strip built around the SMD 3528 package, packed at 240 LEDs per meter, the highest-density single-row strip in the 3528 range. It is the brightest single-colour line you can get on this package, and it runs on a 24V supply, which suits the high power draw at this density. That makes it the pick when you want a strong, near-solid line of light from a single-row strip.
Aperçu des caractéristiques techniques
The strip runs on 24VDC, draws 19.2W per meter and puts out about 1,500 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 10mm wide, cuttable in 25mm steps.
What 240 LEDs per meter means
At 240 LEDs per meter the line reads as nearly solid, with almost no visible gap between the points. It is the highest-output single-row 3528 we make, so it suits task and feature work where you want a strong, even line rather than a soft accent. The trade-off is the power draw, at 19.2W per meter, which is why this version runs on 24V so a long run stays even.
Choosing a colour
This is a static single-colour strip, so each piece is one fixed colour. You pick one of the seven available colours before ordering: red, green, blue, yellow, warm white, commercial white or cool white. It is not an RGB or multicolour strip, so the colour does not change on command. If you want colour changing, that is the 5050 RGB range, a different product.
24V power feeding
This version runs on 24VDC, not 12V. That is the right choice for the 19.2W per meter draw, because 24V drops less voltage over distance, so the whole run stays even. You will need a 24V supply sized for your total meters, and on very long lines you should feed power from both ends so the middle does not dim.
IP rating options
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.
Fabrication et installation
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 10mm wide, so check your cove, channel or gap clears that width before you commit. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.
Contenu de la boîte
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.
Ce que vous devez fournir
You will need a 24VDC power supply sized for your total meters, which the 19.2W per meter figure makes easy to add up. For dimming, a compatible LED dimmer is available. If you are not hard-wiring, use an adapter or driver that matches the 24V supply.
Où est-il utilisé ?
As the brightest single-row 3528 strip it suits task and worktop lighting, high-output coves, display and shop work, and any accent line that needs to carry real light. Outdoors the IP65 and above versions handle eaves, facades and garden edges. The single colours also make it useful for signage and feature lines.
Durée de vie et fiabilité
The SMD 3528 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a properly sized 24V supply and feeding from both ends on long runs, the heat stays manageable even in a tight cove.
