Lampe d'encastre DMX LED RGB/RGBW IG11

What it does

The ILED-IG11 is an underground LED light you set into the ground so it washes a wall, step, bridge, or walkway from below. It is controlled on DMX512, so it is an architectural fixture, not a garden light: a designer codes the colour and brightness and it follows. It is a low-voltage 24V DC unit, so it suits outdoor and splash-proof locations.

Six sizes, one family

The range runs from U1 to U6. U1 is the smallest at ф100mm body, 3 to 6W, and three LED chips. U2 steps up to ф150mm, 3 to 9W, six chips. U3 is ф180mm, 6 to 18W, nine or twelve chips. U4 is ф200mm, 12 to 24W, eighteen chips. U5 is ф250mm, 20 to 32W, twenty-four chips. U6 is the largest at ф320mm, 36 to 48W, thirty-six or forty-eight chips. Each size has its own cut-hole, so measure before you order. The depth is 80 to 100mm depending on the model.

Colour and temperature

Every unit is available in 3K, 4K, 5K, or 6K white, or in RGB, or RGBW. RGB gives red, green, and blue so the unit can change colour. RGBW adds a dedicated white channel to that, which is the one to choose where you want clean white plus colour on the same fixture. The LED source is a discrete Power LED chip, not a COB bar, so the output comes from the chip count in each body.

Beam angles

Choose the beam to match the job. A narrow 5° to 10° beam throws a tight pool or a sharp accent up a face. 15° to 25° spreads that into a defined wash. 45° to 60° covers a wider surface, and 90° is the widest, for a broad, soft flood of a wall or a flight of steps. Because it sits in the ground, a wider beam reads as a soft wash and a narrow one as a crisp pool.

DMX512 control

The ILED-IG11 is wired for DMX512. You can run the built-in controller, or use an external DMX512 source and set each unit to its own address on the line. That lets you sequence the colour and brightness across a row of lights, hold a scene, or run a moving sequence. It is the standard five-wire DMX carry, which separates it from a push-button or app-based inground light.

Daisy-chain connection

Each unit has a 30cm five-wire input cable with a female waterproof connector and a 30cm five-wire output cable with a male connector. You chain them, the output of one feeds the input of the next. The 30cm leads let you space the fixtures to the design. Keep the connectors tight and the line stays sealed at IP67.

Build and materials

The frame is 304 stainless steel, the body is aluminum, and the face is tempered glass. That is the combination that lets it sit in the ground and still take foot traffic, weather, and cleaning without corroding. The aluminum carries the heat off the chips; the tempered glass spreads the light and shields the source. CRI is above 80, so colours read true.

Installation

Each model has a set cut-hole diameter: U1 is ф95mm, U2 is ф135mm, U3 is ф155mm, U4 is ф185mm, U5 is ф235mm, and U6 is ф295mm. Cut the hole in the slab, step, or paving to that diameter, set the unit in, and wire the DMX carry and the 24V DC supply through the end connectors. You need a recess deep enough to seat it flush with the surface.

Power and IP rating

The input is 24V DC, which is the safe low voltage for outdoor and wet locations. The whole unit is rated IP67, so it is sealed against dust and against temporary immersion, not just spray. Feed it from a 24V DC supply sized to the total load on the DMX line, and keep the supply dry and out of the pool area. The 2-year warranty and CE plus RoHS markings cover the fixtures.

Où est-il utilisé ?

Use the ILED-IG11 where you want light to come up out of the ground: bridge soles, steps and stairs, plaza and paving edges, pool surrounds, tree trunks, feature walls, and building fascias. The DMX512 control is what suits a designed display: a steady warm wash on a walkway, a colour scene on a landmark, or a sequenced show for an event. RGBW is the pick where the design wants white and colour on one fixture.

Ce que vous devez fournir

A 24V DC power supply sized to the load. A DMX512 source: the built-in controller, or an external DMX unit you address on the line. The cut-tool for the hole your model specifies. Everything on the fixture, the body, the connectors, and the leads, is in the box.

Why choose the ILED-IG11.

It is an underground LED light built for architectural wash, not a garden spot. Six sizes cover a row of steps to a wide bridge, and each has a set cut-hole so the install lines up. The colour choice is broad: 3K to 6K white, RGB, or RGBW where you want white and colour on one unit. The beam runs from a tight 5° to a soft 90°, so you pick the spread for the surface. It is 304 stainless steel, aluminum, and tempered glass, rated IP67, on a safe 24V DC input. The DMX512 wiring, with 30cm five-wire daisy-chain connectors, is what a lighting designer needs to code a scene or run a display. CRI is above 80. It is CE and RoHS certified with a 2-year warranty. If the job is light up out of the ground, controlled on DMX, this is the fixture.

What is the difference between RGB and RGBW on the ILED-IG11?

RGB mixes red, green, and blue to make colour, so white comes out as a mix of all three and can look a little grey. RGBW adds a dedicated white channel, so the white is clean and bright and the colour channels are still there. Pick RGBW where a design wants both a proper white and coloured scenes on the same fixture. Pick RGB where you only want colour. Both come in the same six sizes.

How do I wire several of them?

Each unit has a 30cm five-wire input cable with a female waterproof connector and a 30cm five-wire output cable with a male connector. You chain them, the output of one feeds the input of the next. On DMX512 you set each unit to its own address on the line, so the controller talks to every fixture separately. Keep the connectors tight and the chain stays sealed at IP67.

What does the 24V DC input mean for the install?

It means you feed the line from a 24V DC power supply, not from the mains directly, which is the safe low voltage for an outdoor or splash-proof location. Size the supply to the total wattage on the DMX line. The supply itself should stay dry and out of the pool. The fixtures are IP67, but the supply is not, so keep it dry.

Which size should I choose?

Match the size to the space and the cut-hole. U1 is the smallest at ф100mm body, 3 to 6W, for a single step or a tight space. U4 at ф200mm, 12 to 24W, suits a wide walkway. U6 at ф320mm, 36 to 48W, is for a large wall or a bridge. The cut-hole sizes run from ф95mm up to ф295mm, so measure the opening you will cut before you order.

What beam angle do I pick?

A narrow 5° to 10° beam is a tight pool or a sharp accent. 15° to 25° is a defined wash. 45° to 60° covers a wider surface, and 90° is the widest for a soft flood of a wall or a flight of steps. Pick the beam to the distance and the surface, and it will read as a clean wash instead of a hot spot.

Use the ILED-IG11 where the light should come up out of the ground. Bridge soles, stair and step edges, plaza and paving lines, pool surrounds, tree trunks, and feature walls are the common spots. The six sizes, from the small U1 up to the large U6, let one row of fixtures cover a narrow step or a wide structure. The DMX512 control is what suits a designed display: hold a steady warm wash on a walkway, set a colour scene on a landmark, or run a sequenced show for an event. Where the design wants white and colour in the same fixture, choose the RGBW version. The beam, from 5° to 90°, sets whether it reads as a tight pool or a broad wash. It is IP67 on a 24V DC input, so it is made for the outdoor, wet locations where you would actually set it into the ground. For a pool surround the IP67 body takes the wash-down, and for a tree line you run several in a row and move the colour across the canopy. CRI above 80 keeps the colours true on the surfaces it lights.

Check these before you buy the ILED-IG11. The six sizes run from U1 at 3 to 6W and ф100mm up to U6 at 36 to 48W and ф320mm, and each has its own cut-hole from ф95mm to ф295mm, so measure the opening first. The colour is 3K, 4K, 5K, 6K white, or RGB, or RGBW, and the beam is any of 5°, 10°, 15°, 25°, 45°, 60°, or 90°. It is IP67 on a 24V DC input, with a 304 stainless steel frame, an aluminum body, and tempered glass. The control is DMX512, wired with 30cm five-wire daisy-chain connectors, which is the reason to pick this line over a plain app or push-button inground light. CRI is above 80, the warranty is 2 years, and it is CE and RoHS certified. A 24V DC supply and a DMX source are not included. If the job is controlled colour up from the ground, this is the fixture.