The ILED-FX-2835 120 is a flexible LED strip built around the SMD 2835 package, packed at 120 LEDs per meter. It is the densest and brightest member of the 2835 range. Where the 60 piece strip is the everyday all-rounder, the 120 piece is the one you reach for when you genuinely need more light from a narrow line, and you are willing to run it on a higher power supply.
Aperçu des caractéristiques techniques
The strip runs on 12VDC or 24VDC, draws 16 to 24W per meter and puts out 1,600 to 2,400 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 10mm wide, cuttable in 25mm steps.
What 120 LEDs per meter means
Doubling the density of the 60 piece strip also doubles the output, so the light looks smoother and brighter with almost no visible gap between LEDs. That makes it the pick for task lighting, bright under-cabinet runs, display work and anywhere you want a strong, even line. The trade-off is the power draw, at 16 to 24W per meter, so it needs a properly sized supply and the 24V version for longer lines.
Dual voltage: 12V or 24V
Because this strip draws twice the current of the 60 piece version, the choice of voltage matters more here. On 12V the voltage drop shows up sooner, so 24V is the better default for anything longer than a short cove. Short, well-fed runs can use 12V, but for corridors, big coves and full-room lines choose 24 so the whole run stays even.
Choosing a white
This is a static white strip, so each piece is one temperature. The three options are warm white for a soft, cosy look in living areas, commercial white for a balanced tone in work and shop spaces, and cool white for a brighter, cleaner light where visibility matters. Pick one before ordering; the strip cannot change temperature on the fly.
IP rating options
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.
Fabrication et installation
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 10mm wide, a touch broader than the 60 piece version, so check your channel or cove clears that width. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.
Contenu de la boîte
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.
Ce que vous devez fournir
You will need a power supply at 12VDC or 24VDC, matched to the strip version, sized for your total meters, which the 16 to 24W per meter figure makes easy to add up. For dimming, a compatible LED dimmer is available. If you are not hard-wiring, use an adapter or driver that matches the strip voltage.
Où est-il utilisé ?
As the brightest option in the 2835 range it suits task and worktop lighting, bright under-cabinet runs, display and shop lighting, and any cove where you want real output. Outdoors the IP65 and above versions handle eaves, facades and garden edges. The three white temperatures cover homes, shops and offices.
Durée de vie et fiabilité
The SMD 2835 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a 24V supply and a properly sized driver the heat stays manageable even in a tight cove.
