Standby Sensor Waterproor LED Ceiling Light IP65 18W

The ILED-BH-R330C MLC is a standby-motion-sensor LED ceiling bulkhead designed for corridor and entrance lighting where automatic on off control is preferred. At φ330mm it is the larger round variant in the R330 series, offering higher lumen output than the compact R145 hublot while maintaining the same IP65 weatherproof construction. The integrated PIR sensor runs at a standby level of 10–20% when no motion is detected, then switches to full output for a user-adjustable hold time when movement is detected.

De LED Panel-Ëmmerung 1200 x 300 (ILED-PL12030-A) ass eng bëlleg, rechteckeg Kanten-Ëmmerung, déi fir linear Dache-Applicatiounen entwéckelt gouf, wou eng gläichméisseg, blendkontrolléiert Beliichtung néideg ass. Déi verlängert Form deckt méi Fläch pro Ëmmerung wéi quadratesch Paneller of, wat d'Gesamtzuel an d'Kabeléierung fir Korridor, Weeër an lang Raim verréngert. Déi 11mm déi bëlleg ass gutt an opgehange Dächer versteckt, ouni d'sicht Plang ze verréngern.

The ILED-BH-R330C MLC runs at a fixed 18W, producing 1980 lumens from a φ330mm housing at 110 lumens per watt. The LED source is LumiLEDs LM80 with a colour rendering index above 82. Input is 220-240VAC or 110-277VAC 50/60Hz, so the fixture works in most regions without a transformer. The colour temperature range is 2800K to 6500K — warm white, neutral and cool white — selectable via a dip-switch inside the housing. The beam angle is 120°, spreading light evenly across the floor plane. Electrical classification is Class II, meaning the fixture is double-insulated and does not require a protective earth connection. The housing base is ABS with a PS diffuser. The complete assembly is IP65 rated — dust-tight and protected against water jets from any direction — making it suitable for covered outdoor locations such as entryways, porches and sheltered walkways.

Corridor motion sensor

The integrated PIR standby motion sensor activates the fixture when movement is detected within its 120° detection arc, up to a maximum mounting height of 3.5 metres. The standby level is factory-set to 10–20% — the fixture remains dimly lit between activations to aid navigation, then switches to full output when motion is sensed. The hold time is adjustable from 30 seconds to 10 minutes via a dip-switch. When set to full-off mode, the fixture remains dark until motion is detected. The sensor is factory-installed inside the housing and cannot be removed or retrofitted after installation.

De Gehäis ass Aluminium mat enger wäisser oder silwener Ënnerfläch. De Diffuseur ass PMMA mat UV-Schutz, behandelt fir Vergëllung iwwer d'Zäit ze resistéieren. Den integrale Regler ass am Gehäis versigeléiert — kee externen Balast oder Stroofsversorger ass néideg. D'Installatioun ass direkt Uerklemmen un 220-240VAC oder 110-277VAC 50/60Hz Netzwierkung, kontrolléiert duerch en Standard-Wannschalter oder e Kretszort. De Panel gëtt an Standard-T-Raster-Dache-Kafelen agebaut, a Schnëttplazen recesséiert oder op der Fläch mat de gelieferten Halterungen opgeschloss. D'11mm Profil läit bal gläich no bei der Dache Plang.

This is a standard standby-motion-sensor bulkhead with no DALI dimming, 0-10V control, or emergency backup. The sensor hold time and standby level are adjustable via internal dip-switches. For projects that require DALI dimming, self-test emergency or photocell control, order the emergency or wall-packed variants from the Halo round 330mm series instead. These variants share the same φ330mm housing but use different internal drivers and control electronics.

Kas ir kastē

Each unit ships as a single bulkhead with the driver and PIR sensor pre-installed, mounting hardware included and the terminal block ready for connection. The selected colour temperature is factory-set via the internal dip-switch — confirm the required setting before ordering, as it cannot be changed after the housing is sealed. No separate controllers, transformers or sensors are packed inside — the fixture is ready to wire direct to mains.

Kur to izmanto

The ILED-BH-R330C MLC is built for corridor and entrance positions where automatic lighting control reduces both energy consumption and maintenance calls. Hotel and office corridors use the standby sensor to keep passages dimly lit between movements. Residential entryways and porch areas benefit from the automatic on off — residents do not need to find a switch in the dark. External walkways and building entrances specify the IP65 seal to handle rain and washdown. Stairwell landings and wider corridor junctions take advantage of the φ330mm size and 1980-lumen output to provide adequate illumination from a single fixture.

Sertifikāti un garantija

The ILED-BH-R330C MLC carries SAA, CE and RoHS certifications. SAA approval covers Australian and New Zealand market requirements. The warranty period is three to five years depending on the region and distributor terms.

Zakaj kupci izberejo te namesto drugih možnosti? To slišimo od strank:

Integrated standby motion sensor. The PIR sensor keeps the fixture at 10–20% standby brightness between activations, providing gentle wayfinding without wasting energy on constant-on lighting. This is a step above standard bulkheads that are either fully on or fully off.

Class II — no earth required. The double-insulated design means the fixture can be installed in locations where a protective earth conductor is not available. This simplifies retrofits in older buildings and reduces installation time.

IP65 in ABS housing. The ABS base and PS diffuser combine with a sealed silicone ring to achieve IP65 protection. This is suitable for covered outdoor locations where a metal housing would corrode over time.

18W delivers 1980 lumens. At 110 lumens per watt the R330C MLC produces more light than the compact R145 hublot while consuming only 18W. This makes it the right size for wider corridors and larger entrance areas.

The Standby Sensor Waterproof LED Ceiling Light (ILED-BH-R330C MLC) is designed for wall and ceiling mounting in interior and exterior locations where automatic corridor lighting is required.

Hotel and office corridors. The standby motion sensor keeps corridors dimly lit between movements, eliminating both the wasted energy of constant-on lighting and the complaint of dark passages. The IP65 seal handles normal indoor dust, and the Class II rating simplifies installation in older buildings without earthing. The 3CCT option lets specifiers match warm-white hospitality zones with cool-white task areas from the same SKU.

Residential entryways and porches. Automatic on off lighting at front doors and back entrances removes the need to find a switch in the dark. The 10–20% standby level provides gentle wayfinding without disturbing sleep, and the IP65 seal protects against rain at uncovered entries.

External walkways and building entrances. These locations combine moisture exposure with a need for reliable automatic illumination. The IP65 weatherproofing handles rain and washdown, while the Class II rating means no earth conductor is needed in older installations.

Stairwell landings and corridor junctions. Wider passage areas benefit from the φ330mm size and 1980-lumen output, which provide adequate illumination from a single fixture. The 120° beam angle spreads light evenly across the floor, and the standby sensor ensures the light is only at full brightness when someone is present.

Einige Dinge, die vor der Bestellung zu prüfen sind:

Colour temperature is factory-fixed. Each SKU is fixed at one colour temperature within the 2800K–6500K range. Confirm the required setting before ordering — it is set via an internal dip-switch and cannot be changed after the housing is sealed.

Sensor hold time is adjustable but fixed at factory. The standby level (10–20%) and hold time (30s–10min) are set via dip-switches inside the housing. Confirm the required sensor behaviour before ordering, as these settings cannot be adjusted after installation without opening the diffuser.

No DALI, emergency or photocell options on this SKU. The ILED-BH-R330C MLC is a standard standby-motion-sensor bulkhead. If the project requires DALI dimming, self-test emergency or photocell control, order the emergency or wall-packed variants from the Halo round 330mm series instead.

Class II — no earth required. The fixture does not need a protective earth conductor. Confirm the installation location does not require earthed equipment for compliance with local regulations.