3 kanála DMX dekóder DMX512

The FEL-CD202 is the 24-channel constant-voltage decoder for the multi-zone strip installs. Twenty-four PWM channels at 3 amps each — eight RGB fittings at three channels apiece, or 24 single-channel outputs — off one box and one DMX address run. The supply auto-ranges across DC5-24V, which makes it the widest power band in the decoder family: 360 watts at 5V, 860 at 12V, 1,720 at 24V. The DMX512/1990 line lands on XLR-3R or the terminal block, the 4096-level decode keeps the fades smooth, and the ten built-in patterns run at 8 speeds where no desk is driving. The body is a compact L125×W52×H40mm at 320g, sitting with the fittings it drives.

Twenty-four channels at 3 amps

The decoder carries 24 constant-voltage PWM channels at 3 amps per channel — up to 72 amps across the box, which is where the power figures come from: 360 watts at 5V, 860 at 12V, 1,720 at 24V. The channel count is what makes it the multi-zone unit: eight RGB fittings take three channels each, eight dual-white fittings take two each with channels to spare, and the single-colour runs take one channel per circuit. The zones decode off twenty-four consecutive DMX addresses, and each channel runs at the voltage the supply delivers.

4096 grey levels

The channels decode at 4096 grey levels — 12-bit resolution. An 8-bit decoder has 256 steps, and the first few of those are visibly chunky when the LEDs dim down; with 4096 steps the same fade moves in increments the eye reads as continuous. Across the eight-zone builds the slow evening shifts hold their line on every zone at once, and the camera-visible installs do not step.

XLR-3R and the terminal block

The DMX512/1990 line lands two ways: the XLR-3R for the stage and event cabling, and the terminal block for the panels and cabinets where the line arrives on stripped conductors. The daisy-chain continues out of whichever connection the run arrived on, decoder to decoder across the zones. The twenty-four channels take twenty-four consecutive DMX addresses, and the addressing is set at the unit.

Laboro envolupon

Working temperature spans -20°C to +55°C, which covers the plant rooms, the ceiling voids and the flight cases the installs travel through. The body is L125×W52×H40mm at 320g — a compact mid-size box, larger than the slim strips and smaller than the big CV units, with the terminals across its face. It sits with the fittings it drives, in the dry, close to the strips it runs.

Kur to izmanto

The decoder earns its place on the multi-zone builds: the hotel frontage where eight zones of RGB run off one box, the restaurant where the coves, the bar and the alcoves share a single decoder, the retail floor where the shelving and the window schemes decode together. Wherever the install needs more channels than a four- or five-channel decoder carries — but not the 24- and 32-channel rail units — this is the set.

Ten patterns, 8 speeds

The decoder carries ten built-in patterns at 8 adjustable speeds — the self-changing programs that hold a look where no desk is running. The shopfront and the unattended installs run their own show off the decoder, and the speed setting tunes the pace of the shift. When the desk arrives, the same unit runs slave under the DMX512/1990 line and the patterns stand down.

Planning the install

Work the load per decoder against the strips: the 3-amp rating per channel and the power band that follows the voltage — 360 watts at 5V, 860 at 12V, 1,720 at 24V. Leave headroom below the per-channel rating rather than loading to it. Size the PSU for the connected load plus margin, land the DMX in and out on the connection the run uses, and give the decoder its start address — the zones take consecutive channels from there. The daisy-chain carries the line to the next decoder on the install.

Choze la deŝifrobildon en la gamo

The DMX decoder family splits by body, channel count and output type. The CD202 is this 24-channel CV multi-zone set on DC5-24V. The CD269 series carries the 24- and 32-channel sets on the DIN rail, and the CD201 is the 32-channel RDM decoder. The slim bodies run the smaller sets — the CD204 single channel at 10 amps, the CD205 two channels at 8, the CD206 three-channel RGB, the CD207 the RGBW with the 9-amp white channel, and the CD208 the RDM decoder with the 16-bit grey scale. The CD206-4 and CD209 are the standalone stage bodies with XLR-3 and RJ45, the CD203 is the large shutter-capable box, the CD23 is the constant-current set for the bare 1-watt LEDs, and the CD250 is the IP67 outdoor unit.

Why do buyers pick the FEL-CD202 over the alternatives? Here is what we hear from customers:
Twenty-four channels off one box. Eight RGB fittings at three channels apiece, or 24 single-channel outputs — the multi-zone builds run off one decoder instead of a stack of four-channel units.
The widest power band in the family. DC5-24V auto-ranging input, at 360 watts of 5V strip, 860 of 12V or 1,720 of 24V.
4096 grey levels. The fades move in 12-bit steps the eye reads as continuous — every zone holds its line on the low end.
Ten patterns at 8 speeds. The self-changing programs hold the standalone looks where no desk is running.
XLR-3R and the terminal block. The stage cabling and the panel conductors land on the same decoder.
3 amps per channel. 72 amps across the box at the ceiling, with the headroom the long multi-zone runs ask for at every zone.

The FEL-CD202 drives the multi-zone strip builds — the 24-channel decoder that runs a whole fitout from one point of control.
Hotel and restaurant fitouts. Coves, bars and alcoves as eight RGB zones off one decoder, the 4096-level fades keeping every zone’s evening shift continuous at once, zone by zone.
Façades and building outlines. Per-floor zones decoded in groups, 24 channels at 3 amps carrying the strips up the elevation.
Retail and window schemes. Shelving, alcoves and window backdrops decoded together, the ten built-in patterns at 8 speeds holding the look outside shop hours.
Stage and event rigs. The XLR-3R taking the desk line, 24 CV channels feeding the strip builds, the patterns covering the soundcheck gaps.
Panel and cabinet installs. The terminal block taking the line where it arrives on stripped conductors, the compact 320g body sitting beside the PSU and the terminations it serves.
For the smaller installs, the slim bodies CD204 to CD208 carry the one-to-four-channel sets; for the rail-mounted high-channel units, the CD269 series runs 24 and 32 channels, and the CD201 is the 32-channel RDM set.