Touche-Dimmer, Wandmontéiert 84 Panel fir LED-Streef-Lichter ILED-DM3 H …

The ILED-DM3 H is a wall-mounted touch dimmer for LED strip lights. It is a small panel you set into a wall, and you dim the strip by touching it, so there is no remote to keep and no switch to guess at. It runs three channels, each at 4A, which is what you need for a multi-zone strip or a strip that needs more than one level of control. It is the pick for a cove, a cove line or a room where you want to set the light with a hand on the wall rather than with a remote on the table.

Wofür es genutzt wird

The unit sits on the wall and runs up to three dimmable channels of LED strip, so you control the level from where you stand, by touch. It dims each channel from 0 to 100 percent, and the dimming is flicker-free, which is what you want on a strip that sits in view. It is the control point for the strip, so you set the level and leave it, rather than hunting for a remote or a switch.

De LED Panel-Ëmmerung 1200 x 300 (ILED-PL12030-A) ass eng bëlleg, rechteckeg Kanten-Ëmmerung, déi fir linear Dache-Applicatiounen entwéckelt gouf, wou eng gläichméisseg, blendkontrolléiert Beliichtung néideg ass. Déi verlängert Form deckt méi Fläch pro Ëmmerung wéi quadratesch Paneller of, wat d'Gesamtzuel an d'Kabeléierung fir Korridor, Weeër an lang Raim verréngert. Déi 11mm déi bëlleg ass gutt an opgehange Dächer versteckt, ouni d'sicht Plang ze verréngern.

The panel takes a 12 to 24V DC supply and gives three channels at 4A each, so the maximum load is 144W at 12V and 288W at 24V. The dimming runs from 0 to 100 percent, and it connects with a DC2.1 or a screw terminal. The panel is 86 by 84 by 60mm at 100g, which is what the 84 panel size refers to, and it works from -30 to 55 degrees.

The three channels

The panel runs three channels, each at 4A, so you can drive up to three zones of strip, or a strip that uses more than one channel, from one panel. If you are running a multi-zone cove, each zone gets a channel and a level of its own, and if you are running a single long strip, you split it across the channels so the panel can control the sections. Work the load against 144W at 12V or 288W at 24V, so each channel stays under its 4A.

Touch dimming, flicker-free

You set the level by touching the panel, which is cleaner than a slider and quicker than a remote. The dimming is flicker-free, so the light does not pulse or shimmer as you change the level, which is the difference between a strip that sits still and one that twitches. It matters most on a strip that is in view, where a flicker is what people notice first.

A panel, not a remote

This is a wall-mounted panel, so it stays where you set it, instead of going in a pocket or on a table. That is the point of it, because a cove or a room is lit from the wall, not from somewhere you have to carry. You set the level at the panel and walk away, and the light stays where you left it.

Connections

The supply comes in on a DC2.1 plug or a screw terminal, so you wire it the way the rest of the install is already run. The three channels go out to the strip, one per channel, and you match the leads to the outputs. Keep the wiring clean and the strip the right voltage, and the panel runs it.

Kas ir kastē

Each unit ships as the panel, with the DC2.1 and the screw terminal on the back. You set it into the wall, wire the supply and the three channels, and it is the point where you set the level of the strip.

Kas jums jānodrošina

You will need a DC supply at 12V or 24V, matched to the strip, sized for the total load on the panel, which is up to 144W at 12V or 288W at 24V. You also need the strip it is driving, and you match the three channels to the strip leads.

Kur to izmanto

Because it is a wall touch dimmer, it shows up in bedrooms and living rooms, in coves and under-cabinet lines, and in commercial spaces where you want to set the light from the wall. It is the pick where you want to dim the strip by hand and keep the control at the point where you stand.

Reliability

It draws up to 144W at 12V or 288W at 24V, so it carries a real load, and the flicker-free dimming is what keeps the light steady at every level. It is rated to work from -30 to 55 degrees, which covers a normal indoor space, and the 84mm panel is small enough to sit on the wall without crowding it.

Here is what installers tell us they like about the ILED-DM3 H:

You dim it by touch. You set the level on the wall, so there is no remote to keep and no switch to guess at. That is the pick for a cove or a room that is lit from where you stand.

Three channels on one panel. It runs up to three zones of strip, so a multi-zone cove or a longer strip gets its own level of control from one panel.

Flicker-free dimming. The light does not pulse or shimmer as you change the level, which is the difference between a strip that sits still and one that twitches.

Easy to wire. It connects with a DC2.1 or a screw terminal, so it fits the way the rest of the install is already run.

Enough for a real strip. At 4A per channel it carries up to 144W at 12V or 288W at 24V, which is a working capacity for a commercial strip load.

A wall touch dimmer for LED strips like this one is used where you want to set the light by hand:

Bedrooms and living rooms. Set the cove or the accent strip from the wall, so the level is at the point where you stand, and you dim it down for the evening without reaching for a remote.

Under-cabinet and cove lines. A multi-zone cove gets its own level on each zone, so the kitchen counter and the feature wall run at different strengths from one panel.

Restaurants and bars. Set the ambient light to suit the room, so a dinner service runs warmer and dimmer and the bar runs brighter, all from the wall panel.

Retail and office interiors. A display line or a reception cove changes with the day, so the light is bright for the work hours and softer for the evening, set from where you stand.

Any room that is lit from the wall. Where you want the control at the point you stand, not on a remote in a pocket, this is the pick, because the panel stays where you set it.

A few things to check before you wire it up:

Match the supply voltage. It takes 12 to 24V DC, so use the voltage the strip runs on. Feeding it the wrong voltage, or the wrong one for the strip, will not run it correctly.

Size the load. Each channel is 4A and the total is 144W at 12V or 288W at 24V. Add up the strip load and keep it under that, and size the supply for it, or the panel will overload.

Match the channels to the strip. The three outputs go to the strip, one per channel, so wire each channel to the right lead, or the zones will run on the wrong output.

Pick the panel spot. It is a touch panel, so set it where you will stand to control the light, and check the wiring reaches it. The 84mm panel is small, so it fits most wall spots.

Keep it off a wet surface. It works to 55 degrees but is an indoor control panel, so keep it dry and out of the weather, which is the usual spot for a wall dimmer.