LED Triproof Light 40W 20W 60W Lamp Fixture IP65 Buckle Lock

The ILED-TPR-B P1 is a basic LED triproof fitting built around a buckle-lock end cap system that removes the need to open the housing during wiring. The P1 designation identifies the 84 × 69 mm narrow-profile version in the ILED-TPR-B range — narrower than the ILED-TPR-A series (90 × 74 mm) and smaller still than the ILED-TPR-C M-series (95–110 mm). It comes in three sizes: 600 mm (20W), 1200 mm (40W), and 1500 mm (60W), covering small corridors to medium bays.

Tech specs

• LED luminous efficacy: 110 lm/W — 2200 lm (600mm/20W), 4400 lm (1200mm/40W), 6600 lm (1500mm/60W)
• Beam angle: 120° wide optical distribution
• Correlated colour temperature: 2800K–7000K broad tunable range (includes warm white)
• CRI: >80
• Power factor: >0.9
• IP rating: IP65 — fully dust-tight, protected against water jets from any direction
• Body & diffuser: PC body + aluminium heat sink + PC diffuser, white or silver finish
• Dimensions: 84 × 69 mm cross-section (narrowest basic triproof in the ILED-TPR range)
• Input voltage: 220–240VAC 50/60 Hz
• Certifications: CE, RoHS, SAA, TUV
• Warranty: 3–5 years

Buckle lock design

The P1’s defining feature is its buckle-lock end cap. Traditional triproof fittings require you to remove the end cap and expose the driver compartment to connect incoming and outgoing cables. The P1’s buckle lock lets you access the terminal block by simply releasing the end cap lever — no tools needed, no need to open the main housing. This cuts installation time and reduces the risk of misplacing small screws or damaging the seal during reassembly.

The lock is rated for repeated opening and closing across the product’s service life. When properly engaged, it maintains the IP65 seal around the end connection point, keeping dust and moisture out of the terminal area.

Installation and maintenance

The P1 is supplied as a complete unit with integral driver. Surface mounting uses the built-in fixing brackets — two points per fixture, suitable for concrete, timber, and metal ceiling structures. The PC diffuser is pre-fitted.

Maintenance is straightforward. The aluminium heat sink provides passive thermal management — no fans or moving parts. In standard conditions the LED source retains above 80% of initial lumens for the life of the warranty period. If the buckle lock mechanism becomes stiff over time, a light cleaning of the latch area with a dry cloth is usually sufficient to restore smooth operation.

Typical applications

The ILED-TPR-B P1 is suited to environments where a basic, tool-free-install triproof fitting is all that is needed. It does not include DALI2 control, emergency backup, or an IK impact rating — those features belong to the ILED-TPR-C M-series. Below are the applications customers specify the P1 for most often.

Storage corridors and light-duty warehouse aisles. — The narrow 84 × 69 mm profile fits where ceiling void space is tight, and the buckle lock means electricians can wire multiple fixtures quickly without carrying tools into the work area.

Car parks and undercroft areas. — IP65 sealing handles damp conditions and occasional wash-down. The broad CCT range (2800–7000K) lets specifiers choose the colour temperature that matches adjacent lighting.

Light assembly workshops and utility rooms. — The PC diffuser provides glare-reduced output suitable for spaces where workers look up frequently. CRI>80 ensures colour accuracy on materials and components.

Supermarket back-of-house and cold storage entrances. — The sealed PC housing tolerates the temperature swing between refrigerated areas and ambient corridors. No IK rating means it is not suited to high-impact zones — use the ILED-TPR-C M-series for those environments.

Retail stockrooms and service passages. — Basic on/off operation is all that is required in these spaces. The P1 delivers reliable illumination at a competitive price point without the added cost of smart control or emergency driver variants.

Why do buyers pick the ILED-TPR-B P1 over other basic triproof fittings? Here is what we hear from customers:

Tool-free buckle lock end caps. The P1’s defining feature is its buckle-lock design, which lets electricians connect wiring by releasing the end cap lever — no tools, no need to open the main housing. On large installations where dozens of fixtures need wiring, this saves significant labour time compared to traditional screw-type end caps.

Narrow 84 × 69 mm profile. The P1 is the narrowest basic triproof in the ILED-TPR range. At 84 × 69 mm it sits between the older ILED-TPR-A series (90 × 74 mm) and the ILED-TPR-C M-series (95–110 mm). When ceiling void space is limited, the slimmer profile is easier to route alongside other services.

Broad CCT range — 2800K to 7000K. Unlike many triproof fittings that offer only neutral white, the P1 spans warm white (2800K) through daylight (7000K). That gives specifiers flexibility to match existing lighting or choose the right tone for the space.

Storage corridors and light-duty warehouse aisles. — The narrow 84 × 69 mm profile fits where ceiling void space is tight, and the buckle lock means electricians can wire multiple fixtures quickly without carrying tools into the work area.

Car parks and undercroft areas. — IP65 sealing handles damp conditions and occasional wash-down. The broad CCT range (2800–7000K) lets specifiers choose the colour temperature that matches adjacent lighting.

Light assembly workshops and utility rooms. — The PC diffuser provides glare-reduced output suitable for spaces where workers look up frequently. CRI>80 ensures colour accuracy on materials and components.

Supermarket back-of-house and cold storage entrances. — The sealed PC housing tolerates the temperature swing between refrigerated areas and ambient corridors. No IK rating means it is not suited to high-impact zones — use the ILED-TPR-C M-series for those environments.

Retail stockrooms and service passages. — Basic on/off operation is all that is required in these spaces. The P1 delivers reliable illumination at a competitive price point without the added cost of smart control or emergency driver variants.

Stock management. — One P1 SKU covers 600 mm, 1200 mm, and 1500 mm lengths with the same 84 × 69 mm profile. Specifying all three sizes together simplifies reordering and reduces SKUs your warehouse holds.

Voltage compatibility. — The P1 accepts 220–240VAC 50/60 Hz. If your project is in a 110V region, confirm the driver variant with your sales contact before ordering — the standard P1 driver is not rated for 110V input.

P1 vs A-series selection. — The P1 has a narrower 84 × 69 mm profile and a tool-free buckle lock end cap. The A-series is wider at 90 × 74 mm with a traditional screw-type end cap. Both are basic on/off triproofs with IP65 and no IK rating. Choose the P1 when space is tight or quick installation matters.

P1 vs M-series comparison. — The P1 is a basic on/off triproof with no DALI2, no emergency option, and no IK impact rating. If your project needs smart control, certified escape lighting, or impact resistance, choose the ILED-TPR-C M-series instead.