DC 12V 24V SMD 5050 30 piece LED per Meter Flexible LED Strip Light

The ILED-FX-5050 30 is a flexible LED strip built on the SMD 5050 package, the largest of the common strip LEDs, laid out at 30 LEDs per meter. It is the entry-density member of the 5050 range, but because each LED is bigger than those on the 3528 and 2835 strips, it still gives a solid, even line of light at low power. That combination makes it a good first choice when you want 5050 output without the very high brightness of the denser 48, 60 and 120 piece versions.

Tech specs at a glance

The strip runs on 12VDC or 24VDC, draws 7.2W per meter and puts out about 600 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 10mm wide, cuttable in 25mm steps.

Why the 5050 package

The 5050 is a bigger die than the 3528 and 2835, so each point is brighter and the light reads as smoother with fewer LEDs per meter. At 30 pieces the strip keeps the power draw modest at 7.2W per meter, which is friendly for long runs and easy to feed. It is not the brightest 5050 you can buy, it is the low-density, economical one.

Colour options

You can have this strip in single colours or in multi-colour. The single colours are red, green, blue, yellow, warm white, commercial white and cool white, one colour per piece. The multi-colour options are RGB and RGB plus White, which add colour mixing and a white channel on the same strip. These are static strips, so the colour is set by a controller or driver rather than addressing each LED separately, which keeps the system simple.

Dual voltage: 12V or 24V

You can have it on 12V or 24. A 12V version pairs with the small transformers used for short cove and cabinet runs. A 24V version drops less voltage down a long line, so it stays even over longer distances. Choose the voltage that fits your supply and the length of the run.

IP rating options

The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.

Build and installation

The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 10mm wide, a touch broader than the 8mm 3528 strips, so check your channel clears that width. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.

What is in the box

Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.

What you need to supply

You will need a power supply at 12VDC or 24VDC, matched to the strip version, sized for your total meters, which the 7.2W per meter figure makes easy to add up. For the RGB and RGB plus White options you also need a compatible controller. For dimming, a compatible LED dimmer is available.

Where it gets used

As an economical 5050 strip it suits cove and ceiling lighting, under-cabinet work, TV and furniture backlight, and general accent lines. The multi-colour versions are the pick for colour changing decoration and signage. Outdoors the IP65 and above versions handle eaves, facades and garden edges.

Lifespan and reliability

The SMD 5050 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a 24V supply and a properly sized driver the heat stays manageable even in a tight cove.

Here is what installers tell us they like about the 5050 30 piece strip:

A bigger LED. The SMD 5050 is the largest common strip package, so each point is brighter and the light reads smoother than a 3528 or 2835 at the same count.

Single and multi-colour. The same strip comes in seven single colours and in RGB and RGB plus White, so you can do a fixed colour or colour changing from one product line.

Dual voltage choice. You can order it on 12V or 24, and for longer lines the 24V version stays even. That saves you from guessing the supply later.

Cut to the exact length. The 25mm cut step means you trim the strip to fit instead of wasting meters or bending a piece that will not sit flat.

Ready to stick. 3M yellow tape is on the back as standard, so most indoor runs do not need any other mounting method.

Entry-density 5050 strips like this one are used a lot for everyday and colour lighting:

Ceiling coves and indirect lighting. Running the strip in a cove line gives an even, smooth glow with no visible source. It is the classic pick for bedroom, lounge and office accent coves that need to stay consistent along a whole wall.

Under-cabinet and under-bed. The 600 lumen per meter is enough to light a worktop, counter or reading zone, and the body tucks away out of sight so the light is what you see.

TV, mirror and furniture backlight. A warm white single colour gives a soft ambient edge, while an RGB or RGB plus White version lets the backlight change colour to match the room or the mood.

Signage and edge accents. The single and multi-colour options are handy where you want a fixed colour or a changing one, such as a store front, a counter edge or a marker line.

Architectural and facade. With IP65 and above, the strip outlines eaves, columns, canopies and garden edges outdoors, weatherproof but still a clean line of light.

A few things to check before ordering:

Pick the colour type first. Single colour runs on its own, but the RGB and RGB plus White options need a matching controller. Buy that at the same time so the install works when it arrives.

Pick the voltage first. Choose 12V for short, easy runs and 24V for longer lines, and buy the matching power supply. Mixing them up is the most common cause of a strip that will not run.

Size the power supply. Multiply your total meters by 7.2W and buy a little above that figure. Undersizing is the most common cause of a strip that dims at the far end.

Match the IP rating to the location. IP20 is dry indoor only. Use IP65 for covered outdoor and wet areas, and IP67 or IP68 for full or harsh exposure.

Check the 10mm width. The 5050 body is broader than the 3528 strips, so make sure your channel, cove or gap clears 10mm before you start cutting.