Round 145mm 8W LED Hublot Light

The ILED-BH-R145 is the compact entry point of the Halo round bulkhead range. At φ145×65mm it is significantly smaller than the R20W (Ø300mm) and R275 (Ø275mm) models, making it the natural choice for narrow doorways, small stairwells and confined wall spaces where a larger bulkhead would look disproportionate. Despite its size, it delivers the same 110 lumens per watt efficiency as the larger models, so specifiers do not sacrifice output for form factor.

Tech specs at a glance

The ILED-BH-R145 is available in two wattage options. The 8W version produces 880 lumens. The 10W version produces 1100 lumens. Both deliver 110 lumens per watt from the same φ145×65mm housing. Input is 220-240VAC or 110-277VAC 50/60Hz, so the fixture works in most regions without a transformer. The colour temperature range is 2800K to 6500K — warm white, neutral and cool white — selectable at installation. Unlike the larger R20W and R275 models, the R145 does not offer 3CCT switchable versions; each SKU is factory-fixed at one colour temperature. Colour rendering is above 82. The beam angle is 120°, spreading light evenly across the floor. Four diffuser variants are available: Plain for general illumination, Grille Crossing (GL) for a softer diffuse pattern, Eyelid Half Moon (EL) for directional wall-washing or facade grazing, and Crossing (TL) for balanced spread with partial glare control. The die-cast aluminium body is IP65 rated — dust-tight and protected against water jets from any direction — and IK10 rated, the highest impact resistance level for lighting equipment.

Build and installation

The housing is die-cast aluminium with a powder-coated finish in white, black or silver gray. The diffuser is anti-UV polycarbonate, available in four patterns as described above. The integral driver is sealed inside the housing — no external ballast or separate power supply is needed. Wiring is direct to mains through the terminal block. Electrical classification is Class I, requiring a protective earth connection. The fixture can be surface-mounted to a flat wall or ceiling using the four mounting points on the back plate. Due to its compact φ145mm diameter, the R145 is ideal for installations where space is limited — door frames, narrow corridors, small landings and tight wall openings.

Control options

This is a standard non-dimmable, non-controlled bulkhead. It switches on and off with the circuit — wall switch, timer or external sensor. For projects that require DALI dimming, motion sensing or emergency backup, order the larger R20W or R275 variants from the Halo round series instead. Those models offer the same IP65+IK10 protection with added control features, but their larger housing (Ø300mm or Ø275mm) means they will not fit the same tight spaces as the R145.

What is in the box

Each unit ships as a single bulkhead with the driver pre-installed, mounting hardware included and the terminal block ready for connection. The selected diffuser (Plain, GL, EL or TL) is factory-fitted and should not be removed after installation. No separate controllers, transformers or drivers are packed inside — the fixture is ready to wire direct to mains.

What you need to supply

A circuit breaker or wall switch for on/off control. A mounting surface suitable for the fixture weight. For outdoor installations, confirm the mounting location is within the IP65 protection zone and that the seal remains intact after installation. No special tools beyond a screwdriver and wire strippers are required.

Where it gets used

The ILED-BH-R145 is built for locations where the compact φ145×65mm housing is an advantage rather than a compromise. Residential front doors and back doors use the small footprint to provide security lighting without overwhelming the doorway. Apartment entrance corridors and stairwells benefit from the compact size — multiple units can be spaced closely along narrow walls without visual clutter. Hotel room corridors and bathroom doorways specify the R145 for the same reason: it delivers adequate illumination in tight spaces where a larger bulkhead would dominate the wall. External gateways, porch areas and balcony walls take advantage of the IP65 weatherproofing and the choice of diffuser patterns to控制 light spread and glare. The four diffuser options let a single compact housing serve general wash areas (Plain), softer diffuse paths (GL), directional accent positions (EL) or balanced spill (TL).

Certifications and warranty

The ILED-BH-R145 carries SAA, CE and RoHS certifications. SAA approval covers Australian and New Zealand market requirements. The warranty period is three to five years depending on the region and distributor terms.

Why do buyers pick these over the alternatives? Here is what we hear from customers:

Compact size fits tight spaces. At φ145×65mm the R145 is the smallest round bulkhead in the Halo series. Doorways, narrow corridors and small landings where a larger fixture would look too big are the primary use case.

Four diffuser options from one family. The R145 is available in Plain, Grille Crossing (GL), Eyelid Half Moon (EL) and Crossing (TL) diffusers. All four share the same housing and mounting pattern, so specifiers can mix patterns across a project without changing fixture dimensions or wiring.

Same 110LM/W efficiency as larger models. Despite its small size, the R145 delivers 110 lumens per watt — matching the output efficiency of the R20W and R275. Specifiers get compact form factor without sacrificing lumen output per watt.

IP65+IK10 in a small package. The die-cast aluminium housing combines weatherproof sealing with the highest impact resistance rating. This is unusual for a bulkhead of this size and makes the R145 suitable for high-traffic exterior positions.

The Round 145mm LED Hublot Light (ILED-BH-R145) is designed for wall and ceiling mounting in interior and exterior locations where a compact fixture is required.

Residential front doors and back doors. The φ145mm diameter fits door frames and narrow wall spaces where a larger bulkhead would overwhelm the opening. The IP65 seal handles rain and washdown at entry points, and the IK10 rating resists accidental impact from packages and feet.

Apartment entrance corridors and stairwells. Narrow passages in multi-unit buildings benefit from the compact form — multiple R145 units can be spaced closely along the wall without visual clutter. The IP65 seal handles normal corridor dust, and the choice of diffuser patterns lets specifiers control light spread for shared circulation areas.

Hotel room corridors and bathroom doorways. Compact bulkheads at room entrances provide subtle wayfinding illumination without dominating the wall. The four diffuser options let specifiers match the light pattern to the corridor width — Plain for wider halls, GL for softer diffusion in narrow passages.

External gateways and porch areas. These locations combine moisture exposure with a need for compact, unobtrusive lighting. The IP65 weatherproofing and IK10 impact resistance handle both rain and the occasional bump from passing bags or bicycles. The 110LM/W efficiency keeps energy costs low for 24-hour gateway illumination.

A few things to check before ordering:

Colour temperature is factory-fixed. Unlike the larger R20W and R275 models, the R145 does not offer 3CCT switchable versions. Each SKU is fixed at one colour temperature within the 2800K–6500K range. Confirm the required colour temperature before ordering — it cannot be changed after installation.

No DALI, emergency or motion sensor options. The R145 is a standard non-dimmable, non-controlled bulkhead. If the project requires DALI dimming, motion sensing or emergency backup, order the R20W or R275 variants from the Halo round series instead. Those models share the same IP65+IK10 protection but offer additional control features.

Diffuser selection. Four variants are available from the same housing: Plain for general illumination, Grille Crossing (GL) for a softer diffuse pattern, Eyelid Half Moon (EL) for directional wall-washing or facade grazing, and Crossing (TL) for balanced spread with partial glare control. Confirm the required pattern before ordering — the diffuser is factory-fitted and cannot be swapped after installation.