The ILED-HB5 120W is a flat-panel LED high bay luminaire with integrated reflector, designed for pendant mounting in warehouses, factories, retail stores and commercial buildings with ceiling heights between 3 m and 8 m. The HB5 series covers four wattage models — 100W, 120W, 150W and 200W — all delivering 130 lm/W from LumiLEDs 3030 LEDs inside a slim φ200 mm cylindrical body. Optional DALI 2-way dimming, emergency battery backup and corridor-mode motion sensor provide upgrade paths for building automation and egress compliance.
Aperçu des caractéristiques techniques
Models: ILED-HB5 100W / 120W / 150W / 200W
Luminous efficacy: 130 lm/W (all models)
Lumen output: 13,000 lm (100W) / 15,600 lm (120W) / 19,500 lm (150W) / 26,000 lm (200W)
Housing diameter: φ200 mm (all models)
Housing depth: 70 mm (100W) / 100 mm (120W/150W) / 150 mm (200W)
LED source: LumiLEDs 3030 SMD
Beam angle: 120° (standard); other angles available on request
Color temperature: 2800K – 6500K (user-adjustable dip switch)
CRI: >82
Input voltage: 220–240VAC / 110–277VAC dual-range
Power factor: >0.9
IP rating: IP65 — dust-tight, protected against water jets
Impact rating: IK10 — 5 joules resistance
Materials: Aluminium body, PC diffuser, black finish
Electrical classification: Class I
Certifications: SAA, CE, RoHS
Warranty: 3–5 years
Optional features: DALI 2-way dimming, emergency battery, motion sensor
Build and impact resistance
The HB5 housing is a slim cylindrical aluminium body (φ200 mm) with depths ranging from 70 mm (100W) to 150 mm (200W). The extended depth at higher wattages accommodates a larger heat sink and driver compartment while maintaining a low-profile aesthetic suitable for visible ceiling installations in retail and commercial spaces.
The PC diffuser carries an IK10 impact rating — the highest standard for luminaires — absorbing a 5 joule impact (roughly a 1 kg mass dropped from 50 cm) without cracking. For warehouse and industrial settings where forklifts, overhead cranes and falling tools are routine, IK10 reduces replacement costs and liability over the warranty period. The IP65 seal protects the internal driver and LED array from dust and water jets, suitable for wash-down areas and unconditioned roof spaces.
Control and installation
The HB5 series offers three optional upgrades: DALI 2-way dimming, emergency battery backup, and a corridor-mode motion sensor. These are not combined in a single SKU — select the features you need at order time.
DALI 2-way dimming adds individual fixture addressing (0–63) on a 2-wire bus, allowing group control, scene setting, and status feedback including lamp hours and fault codes. Up to 64 fixtures share one line. The HB5 does not accept 0-10V or TRIAC analog dimming — a DALI-to-analog converter is required if your building system uses those protocols.
The emergency battery provides approximately 90 minutes of light at reduced output during a power failure, satisfying egress lighting requirements in many jurisdictions. The corridor-mode motion sensor keeps the fixture at low stand-by output (around 30%) when unoccupied, then ramps to full brightness within 1–2 seconds of detecting movement — effective in storage aisles and low-traffic zones.
Installation uses a pendant-mount eyelet with an adjustable steel cable, hanging the fixture from the ceiling structure or mounting directly to a flat soffit. The Class I rating requires a protective earth connection. Universal 110–277VAC input covers both North American and European supply standards. The 120° standard beam angle provides wide, even coverage ideal for general illumination in spaces with ceiling heights between 3 m and 8 m.
