The ILED-FX-5050 120 is a flexible LED strip built on the SMD 5050 package at 120 LEDs per meter, the densest and brightest version in the 5050 range. It is the one you reach for when you want a strong, even line of light from a single strip, or a solid colour line with barely any gap between the points. It runs on a 24V supply, which suits the higher power draw at this density.
Aperçu des caractéristiques techniques
The strip runs on 24VDC, draws 28.8W per meter and puts out about 2,200 lumen per meter with a 120 degree spread. Colour rendering is CRI above 80 as standard and above 90 on request. Each piece ships as a 5 meter roll, 13.5mm wide, cuttable in 25mm steps.
Why the 5050 package
The 5050 is a bigger die than the 3528 and 2835, so each point is brighter and the light reads as smoother. Packed at 120 LEDs per meter it gives a near-solid line, which is why it is used where a softer, lower-count strip would look too sparse. The trade-off is the power draw, at 28.8W per meter, and the wider 13.5mm body.
What 120 LEDs per meter means
Doubling the density of a 60 piece strip doubles the output, so the light is brighter and the spacing almost disappears. It suits task and display work, high-output coves and any line that needs to carry real light. Because the draw is high, run it on 24V and feed long lines from both ends so the middle stays even.
Colour options
You can have this strip in single colours or in multi-colour. The single colours are red, green, blue, yellow, warm white, commercial white and cool white, one colour per piece. The multi-colour options are RGB and RGB plus White, which add colour mixing and a white channel on the same strip. These are static strips, so the colour is set by a controller rather than addressing each LED separately.
24V power feeding
This version runs on 24VDC, not 12V. That is the right choice for the 28.8W per meter draw, because 24V drops less voltage over distance, so the run stays even. You will need a 24V supply sized for your total meters, and for very long lines feed power from both ends.
IP rating options
The same strip is offered in four protection ratings. IP20 is for dry indoor locations such as coves and cabinetry. IP65 handles covered outdoor and wet areas like eaves and facades. IP67 and IP68 are for where the strip gets fully wet or sits in harsh coastal air. Match the rating to the location, not the highest one on the list.
Fabrication et installation
The strip cuts cleanly in 25mm steps, so you trim it to fit instead of bending a longer piece. It is 13.5mm wide, the broadest in the 5050 range, so check your channel, cove or gap clears that width before you commit. It is backed with 3M yellow double-sided tape, and a 3M red tape is available on request. A 15cm input cable is fitted to the leading end, and connector cables can be customized to a different length or plug.
Contenu de la boîte
Each order ships with the strip as a 5 meter roll, the 3M yellow mounting tape, and the 15cm input cable on the connection end. Custom lengths are cut to order from the same roll.
Ce que vous devez fournir
You will need a 24VDC power supply sized for your total meters, which the 28.8W per meter figure makes easy to add up. For the RGB and RGB plus White options you also need a compatible controller. For dimming, a compatible LED dimmer is available.
Où est-il utilisé ?
As the brightest option in the 5050 family it suits task and worktop lighting, high-output coves, display and shop work, and colour changing decoration and signage. Outdoors the IP65 and above versions handle eaves, facades and garden edges.
Durée de vie et fiabilité
The SMD 5050 LEDs carry a 50,000 hour rated life, which at typical use is well past a decade. There are no moving parts and no fan, so the strip does not fail through heat. It works from -20 C to 50 C, and with a properly sized 24V supply and feeding from both ends on long runs, the heat stays manageable even in a tight cove.
