The ILED-HB5 150W is a flat-panel LED high bay luminaire with integrated reflector, designed for pendant mounting in warehouses, factories, retail stores and commercial buildings with ceiling heights between 3 m and 8 m. The HB5 series covers four wattage models — 100W, 120W, 150W and 200W — all delivering 130 lm/W from LumiLEDs 3030 LEDs inside a slim φ200 mm cylindrical body. The 150W model sits in the middle of the range, producing 19,500 lm from a 100 mm deep housing — suitable for spaces requiring more output than the 120W without reaching the 200W maximum.
Aperçu des caractéristiques techniques
Model: ILED-HB5 150W
Wattage: 150W (fixed)
Lumen output: 19,500 lm
Luminous efficacy: 130 lm/W
Housing diameter: φ200 mm
Housing depth: 100 mm
LED source: LumiLEDs 3030 SMD
Beam angle: 120° (standard); other angles available on request
Color temperature: 2800K – 6500K (user-adjustable dip switch)
CRI: >82
Input voltage: 220–240VAC / 110–277VAC dual-range
Power factor: >0.9
IP rating: IP65 — dust-tight, protected against water jets
Impact rating: IK10 — 5 joules resistance
Materials: Aluminium body, PC diffuser, black finish
Electrical classification: Class I
Certifications: SAA, CE, RoHS
Warranty: 3–5 years
Optional features: DALI 2-way dimming, emergency battery, motion sensor
Series comparison
The HB5 150W shares its φ200 mm housing diameter with the entire HB5 series but differs in depth and output. The 100W model has a 70 mm depth and produces 13,000 lm; the 120W and 150W share a 100 mm depth, producing 15,600 lm and 19,500 lm respectively; the 200W increases to 150 mm depth and 26,000 lm. All four models deliver 130 lm/W and carry the same IP65+IK10 ratings, CRI >82 standard, and 2800–6500K CCT range.
The 150W occupies a practical middle ground — sufficient output for high-ceiling retail spaces and warehouse aisles where the 120W falls short, without the larger footprint and higher cost of the 200W. When selecting between models, match the lumen output to your ceiling height and illuminance target: spaces above 6 m generally benefit from the 150W or 200W, while 3–6 m ceilings may be adequately served by the 100W or 120W.
Build and impact resistance
The HB5 150W housing is a slim cylindrical aluminium body (φ200 × 100 mm) with a black powder-coat finish. The extended depth relative to the 100W model accommodates a larger heat sink and driver compartment while maintaining the same low-profile aesthetic suitable for visible ceiling installations in retail and commercial spaces.
The PC diffuser carries an IK10 impact rating — the highest standard for luminaires — absorbing a 5 joule impact (roughly a 1 kg mass dropped from 50 cm) without cracking. For warehouse and industrial settings where forklifts, overhead cranes and falling tools are routine, IK10 reduces replacement costs and liability over the warranty period. The IP65 seal protects the internal driver and LED array from dust and water jets, suitable for wash-down areas and unconditioned roof spaces.
Control and installation
The HB5 150W offers three optional upgrades: DALI 2-way dimming, emergency battery backup, and a corridor-mode motion sensor. These are not combined in a single SKU — select the features you need at order time.
DALI 2-way dimming adds individual fixture addressing (0–63) on a 2-wire bus, allowing group control, scene setting, and status feedback including lamp hours and fault codes. Up to 64 fixtures share one line. The HB5 does not accept 0-10V or TRIAC analog dimming — a DALI-to-analog converter is required if your building system uses those protocols.
The emergency battery provides approximately 90 minutes of light at reduced output during a power failure, satisfying egress lighting requirements in many jurisdictions. The corridor-mode motion sensor keeps the fixture at low stand-by output (around 30%) when unoccupied, then ramps to full brightness within 1–2 seconds of detecting movement — effective in storage aisles and low-traffic zones.
Installation uses a pendant-mount eyelet with an adjustable steel cable, hanging the fixture from the ceiling structure or mounting directly to a flat soffit. The Class I rating requires a protective earth connection. Universal 110–277VAC input covers both North American and European supply standards. The 120° standard beam angle provides wide, even coverage ideal for general illumination in spaces with ceiling heights between 3 m and 8 m.
