LED Triproof Light 40W 20W 60W Lamp Fixture IP65 Buckle Lock

The ILED-TPR-B P1 is a basic LED triproof fitting built around a tool-free buckle-lock end cap. You release the lever, wire the terminal block, and close it up without opening the main housing or carrying tools. It is the narrow 84 by 69 mm body in the ILED-TPR-B range, in three lengths: 600 mm at 20W, 1200 mm at 40W, and 1500 mm at 60W. It is meant for places where you want a dependable, sealed fitting and nothing more: no smart control, no emergency, no impact rating.

Tekniska specifikationer i korthet

Efficiency runs at 110 lumens per watt, so the 60W version puts out 6600 lumens and the 20W version 2200. The colour temperature is tunable across a broad range, 2800K to 7000K, which is wider than most basic triproofs. The beam is 120 degrees, so one fixture covers a wide area under a ceiling. The full parameter list, the exact lumen figure per size, the IP rating, the power factor, and the certifications, is in the specification table above. This description focuses on the design choices that matter when you install the fitting.

The buckle lock

The defining feature is the buckle-lock end cap. A traditional triproof means removing the end cap and exposing the driver compartment to connect the cables. The P1 opens the terminal area by releasing a lever, no tools, no need to open the main body. That cuts the time it takes to wire a row of fixtures and removes the small screws that usually get lost during reassembly. The lock is made for repeated opening and closing, and when it is engaged it holds the IP65 seal around the end connection, keeping dust and moisture out of the terminal area.

Montering och installation

The body is polycarbonate, with an aluminium heat sink and a polycarbonate diffuser. The diffuser is pre-fitted, and the heat sink manages the heat passively, so there are no fans or moving parts to fail. It surface-mounts on the built-in brackets, two fixing points per fixture, onto concrete, timber, or metal. It runs on 220 to 240VAC, and it is Class II, so it does not need a separate earth connection, which keeps the wiring simpler on a retro-fit. It comes in a white painted or silver finish.

What it does not include

The P1 is a basic on-off fitting. It has no DALI2, no 0-10V dimming, no motion sensor, no emergency backup, and no IK impact rating. Those are on the ILED-TPR-C M-series. If your project needs any of them, that is the model to specify instead. The P1 is the low-cost, tool-free, sealed fitting for where none of those features are wanted.

Var den används

Use the P1 in storage corridors and light-duty warehouse aisles, car parks and undercrofts, light assembly workshops, utility rooms, supermarket back-of-house, and retail stockrooms. The narrow profile suits tight ceiling voids, and the IP65 seal handles damp and occasional wash-down. It is not for high-impact zones or fully exposed outdoors, so for those locations use the M-series.

Vad du behöver ta med dig

The fitting comes complete with its integral driver. You supply the 220 to 240VAC supply and the mounting surface. The diffuser is pre-fitted and the buckle lock is tool-free, so you do not need a special tool kit on site. Keep the supply within the rated range and the fitting holds up.

Livslängd och tillförlitlighet

The sealed polycarbonate body, the passive aluminium heat sink, and the integral driver are the parts that keep it going, and the supplier backs the fitting with a 3 to 5 year warranty. With no moving parts, the main upkeep is to keep the latch area clean so the buckle stays smooth. If it starts to feel stiff, a light wipe of the latch is usually all it takes.

Why do buyers pick the ILED-TPR-B P1 over other basic triproof fittings? Here is what we hear from customers:

Tool-free buckle lock end caps. The P1’s defining feature is its buckle-lock design, which lets electricians connect wiring by releasing the end cap lever — no tools, no need to open the main housing. On large installations where dozens of fixtures need wiring, this saves significant labour time compared to traditional screw-type end caps.

Narrow 84 × 69 mm profile. The P1 is the narrowest basic triproof in the ILED-TPR range. At 84 × 69 mm it sits between the older ILED-TPR-A series (90 × 74 mm) and the ILED-TPR-C M-series (95–110 mm). When ceiling void space is limited, the slimmer profile is easier to route alongside other services.

Broad CCT range — 2800K to 7000K. Unlike many triproof fittings that offer only neutral white, the P1 spans warm white (2800K) through daylight (7000K). That gives specifiers flexibility to match existing lighting or choose the right tone for the space.

Storage corridors and light-duty warehouse aisles. — The narrow 84 × 69 mm profile fits where ceiling void space is tight, and the buckle lock means electricians can wire multiple fixtures quickly without carrying tools into the work area.

Car parks and undercroft areas. — IP65 sealing handles damp conditions and occasional wash-down. The broad CCT range (2800–7000K) lets specifiers choose the colour temperature that matches adjacent lighting.

Light assembly workshops and utility rooms. — The PC diffuser provides glare-reduced output suitable for spaces where workers look up frequently. CRI>80 ensures colour accuracy on materials and components.

Supermarket back-of-house and cold storage entrances. — The sealed PC housing tolerates the temperature swing between refrigerated areas and ambient corridors. No IK rating means it is not suited to high-impact zones — use the ILED-TPR-C M-series for those environments.

Retail stockrooms and service passages. — Basic on/off operation is all that is required in these spaces. The P1 delivers reliable illumination at a competitive price point without the added cost of smart control or emergency driver variants. For a warehouse aisle or a covered car park, the P1 is the low-cost, tool-free choice; where the same space also needs impact protection or dimming, step up to the ILED-TPR-C M-series instead.

Stock management. — One P1 SKU covers 600 mm, 1200 mm, and 1500 mm lengths with the same 84 × 69 mm profile. Specifying all three sizes together simplifies reordering and reduces SKUs your warehouse holds.

Voltage compatibility. — The P1 accepts 220–240VAC 50/60 Hz. If your project is in a 110V region, confirm the driver variant with your sales contact before ordering — the standard P1 driver is not rated for 110V input.

P1 vs A-series selection. — The P1 has a narrower 84 × 69 mm profile and a tool-free buckle lock end cap. The A-series is wider at 90 × 74 mm with a traditional screw-type end cap. Both are basic on/off triproofs with IP65 and no IK rating. Choose the P1 when space is tight or quick installation matters.

P1 vs M-series comparison. — The P1 is a basic on/off triproof with no DALI2, no emergency option, and no IK impact rating. If your project needs smart control, certified escape lighting, or impact resistance, choose the ILED-TPR-C M-series instead.