LED Wall Pack Light 40W-120W Meanwell Driver

Quality Assurance: Rigorous testing and premium components ensure long-lasting performance.

Expert Support: Our engineering team provides full technical support for your projects.

Fast Delivery: Global logistics network ensures your products arrive on time.

Is this dimmable? Yes, compatible with most PWM dimmers.

Can it be cut? Yes, cuttable every 50mm.

What is the warranty period? We offer a standard 3-year warranty on all our premium LED lighting systems.

Building entrances and perimeters.
— The WP1’s 120° beam provides even wall wash at building entrances and perimeter walls. IP65 seal withstands rain and wind-driven spray. IK10 protects against vehicle and equipment strikes.

Parking lots and car parks.
— Perimeter-mounted WP1 provides spill light onto parking areas, reducing pole fixture counts. The 110W–120W model covers wide zones; the 40W–60W suits narrow aisles. IK10 is essential where vehicle doors and ladders may strike.

Loading docks and service entrances.
— Die-cast aluminum body withstands loading dock temperature extremes, vibration and impact. IP65 seal protects against wash-down cleaning and rain through open dock doors. Optional emergency battery covers egress during power failures.

Security and access point lighting.
— The WP1’s CRI >82 renders faces, vehicle colours and security tags in natural colour, improving facial recognition and CCTV footage quality. When paired with the optional motion sensor, the WP1 can operate at low stand-by output to deter loitering while conserving energy, then ramp to full brightness within 1–2 seconds of detecting movement at access points.

Three wattage ranges in one housing.
— The WP1 is available as 40W–60W, 70W–100W or 110W–120W, all sharing the same 333 × 250 × 159 mm die-cast aluminum housing. This means you can mix wattage ranges on the same project without changing mounting hardware or conduit sizes — ideal for phased installations or mixed-application sites.

IK10 impact resistance.
— The WP1 carries an IK10 rating — the highest standard for luminaires — absorbing a 5 joule impact without cracking. For wall pack lights installed at accessible heights near parking areas and loading docks, IK10 significantly reduces replacement costs from vehicle and equipment strikes.

IP65 outdoor rated.
— The WP1 is sealed against dust and water jets, suitable for direct outdoor exposure without additional weatherproofing. The die-cast aluminum body provides inherent corrosion resistance, important for coastal or de-icing-salt environments.

DALI, sensor and emergency options.
— All three optional features are available on the WP1 platform, but each must be selected at order time — they are not retrofittable. Plan your control and safety requirements before placing the order.

Q: What are the three wattage models of the WP1?
A: The WP1 is offered in three fixed wattage ranges: 40W–60W (entry-level), 70W–100W (mid-range) and 110W–120W (highest output). All three share the same 333 × 250 × 159 mm housing and 110 lm/W efficacy — the only difference is power consumption and lumen output. Choose the 110W–120W model for wide parking areas and large façades; the 40W–60W model for narrow walkways and low-ceiling perimeter lighting.

Q: Is the WP1 suitable for direct outdoor installation?
A: Yes. The WP1 carries IP65, which protects against dust and water jets from any direction, making it suitable for unsheltered outdoor mounting on building exteriors, parking structures and covered walkways. It is not rated for direct submersion.

Q: Can the WP1 be dimmed with a standard wall switch?
A: The base WP1 is on/off only. If dimming is required, specify the DALI 2-way dimming option at order time. The WP1 does not accept 0-10V or TRIAC analog dimming — a DALI-to-analog converter is required if your building system uses those protocols.

Q: Does the WP1 have a built-in motion sensor?
A: No. The corridor-mode motion sensor is an optional upgrade selected at order time — it is not built into the standard WP1. If occupancy sensing is required for energy savings, specify the sensor option when ordering.

Q: What is the emergency battery duration?
A: The optional emergency battery provides approximately 90 minutes of light at reduced output during a power failure, satisfying egress lighting requirements in most jurisdictions. The battery is not replaceable in the field — plan for complete unit replacement at end of battery life.

Q: Can I mix different WP1 wattage models on the same project?
A: Yes. All three WP1 models share the same 333 × 250 × 159 mm housing, mounting pattern and wiring terminal layout. You can mix wattage ranges on the same project without modifying mounting brackets or conduit sizes — select each model according to the illuminance requirements of its specific location.

Housing identical across all wattage ranges. — All three WP1 wattage models share the same 333 × 250 × 159 mm housing. Mixing ranges on one project requires no bracket or conduit changes — select each model for its location’s illuminance needs.

DALI is optional, not standard. — Base WP1 is on/off only. DALI 2-way is an optional upgrade at order time. No 0-10V or TRIAC support — a DALI-to-analog converter is required for those protocols.

Motion sensor is optional. — Corridor-mode motion sensor is an optional upgrade at order time — not built in, not retrofittable. Include it if occupancy sensing is a project priority.

Emergency battery is optional. — Emergency battery is not standard on the WP1 — specify at order time. If egress lighting is required at your entrances, confirm the option before ordering; it cannot be retrofitted.

Gray finish standard. — The WP1 ships with a gray powder-coat finish as standard on the die-cast aluminum body. This neutral colour blends into most commercial and industrial building façades without drawing attention to the fixture itself. Custom colours are available as special orders at additional cost.